Jump to content
SAU Community

Wideband O2 Sensor - Aem Uego

D_Stirls

By D_Stirls,
in South Australia

 Share

Recommended Posts

D_Stirls Veteran

D_Stirls

Posted
Posted (edited)

Hello all,

I'm going to be ordering a wideband O2 in the next 2 weeks and have found a really good price. Only really interested organising it for SA people as people will have to pick them up from me in Campbelltown, that way i don't have to stuff around with postage.

I have read a number of reviews and they are one of the best budget O2 sensor available. Generally they are around $250 mark. They also come with two gauge faces and two bezels so you can set them up to match your other gauges.

you can setup one of the output wires to simulate the factory Nerst cell (factory O2 sensor) signal so you can remove the factory O2 and just use the UEGO signal to control your ECU in closed loop.

Digital Wideband Air / Fuel Gauge

A wideband UEGO sensor controller accurately monitors Air/Fuel ratios (AFR) during the tuning process to prevent a lean fuel mixture, which could lead to engine damage. AEM has combined its single-channel wideband UEGO controller and gauge display into one unit, uniting unsurpassed AFR accuracy and control with an easy-to-read interface. AEM’s Gauge-Type Wideband UEGO Controller features a digital LED display and sweeping LED “needle” that changes colors as AFR changes from rich to lean. The unit’s 52mm (2-1/16”) gauge housing fits in most gauge pods and can be remotely mounted virtually anywhere.

  • Ideal AFR monitoring tool for EFI and carbureted applications, and engine dynamometers
  • Does not oscillate AFR reading like narrow band sensors
  • No laptop required for monitoring!
  • Bosch sensor included
  • Accurate to 0.1 AFR
  • Reads in AFR or Lambda via a switch in back of gauge housing
  • 24 Color-coded LED display lights provide immediate reference to engine’s air/fuel ratio (AFR) or Lambda ratio
  • Integrated three-digit display reveals AFR or Lambda in real time
  • User-programmable 0-5v analog output included for use with data loggers and virtually any engine management system
  • Serial data stream included for output of AFR (RS 232)

aemuegologo.jpg

Edited by heslo
Link to comment
https://www.sau.com.au/forums/topic/345742-wideband-o2-sensor-aem-uego/
Share on other sites
D_Stirls Veteran

D_Stirls

Posted
  • Author
Posted (edited)

Seems to be just power and earth is needed, the Sensor just clips in to a loom and if you are going to use the Wide band to simulate the narrow band signal then there is one other wire than need to be wired in, but since your running a GTR you would need two so i would suggest getting the bung welded into the dump where the two front pipes meet.

Here's the manual;

AEM_UEGO_Wide_Band_AFR_Installation_Instructions_30_4100.pdf

Still looking for cheaper prices, it's looking like they will be at or around the $200 mark from Australia. Hearing back from a dealer in the next couple days.

Edited by D_Stirls
D_Stirls Veteran

D_Stirls

Posted
  • Author
Posted

Ok Guys i have found a seller in Australia and The price is $200 and the order will be put in at the end of this week or the beginning of next. So if you want to get in on this PM me and i'll send you that bank details.

I would prefer to have people pick them up but if you really need it to be posted i'll put it in an express post bag (which i think is $15).

I found out that the reason the international sellers wouldn't send them overseas was because the warranty only covers the country they are sold in; so if i brought them in from the states they wouldn't have a warranty.

So these have a warranty as they are from an Australian seller.

D_Stirls Veteran

D_Stirls

Posted
  • Author
Posted

Ok Guys i have found a seller in Australia and The price is $200 and the order will be put in at the end of this week or the beginning of next. So if you want to get in on this PM me and i'll send you that bank details.

I would prefer to have people pick them up but if you really need it to be posted i'll put it in an express post bag (which i think is $15).

I found out that the reason the international sellers wouldn't send them overseas was because the warranty only covers the country they are sold in; so if i brought them in from the states they wouldn't have a warranty.

So these have a warranty as they are from an Australian seller.

Apparently PM are down for the time being.

Just email me on; [email protected]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • niZmO_Man
      Lock up the old for sale / wtb threads.

      By niZmO_Man · Posted

      There is a warning that "this thread is super old" but they ignore that anyway...
    • TurboTapin
      Ethanol Content Sensor - Always at 11%?

      By TurboTapin · Posted

      With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...