Jump to content
SAU Community

Recommended Posts

would u be concerned if it was higher than ur last? :)

there have been a couple of people from this forum who have dynoed there cars on other dynos like BMT and the ones the guys from ICE use and then without any changes had them dynoed on the AVO pulleys with about a 10kw+ difference...

nothing major...

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

hahahaha dont listen to them mupkant, buy a killer handling setup and kick some ass when you get to round-a-bouts and other such turns (of course, ones that are on your own private test tracks, you know....)

hahahaha dont listen to them mupkant, buy a killer handling setup and kick some ass when you get to round-a-bouts and other such turns (of course, ones that are on your own private test tracks, you know....)

i have nightmares about roundabouts, while back ago

sorta speed through a round a bout during wet road...and

lets just say i got really close to saying hello to the 'keep left' sign.

I aint implying anything. Its just that they use a dyno around the corner from their place if they are only running 1 car, so they dont have to drive all the way to bayswater and back and waste half a day. Plus with those minimal mods u can get false readings unless u go to joe blogs backyard dyno and reel off 200rwkw after the secret mods joe blogs has done on your car ;)

I aint implying anything. Its just that they use a dyno around the corner from their place if they are only running 1 car, so they dont have to drive all the way to bayswater and back and waste half a day. Plus with those minimal mods u can get false readings unless u go to joe blogs backyard dyno and reel off 200rwkw after the secret mods joe blogs has done on your car ;)

hehe lol

why did you have to crush my hopes of my car giving good performance ;)

maybe a 1/4 time should really show its real power?

oh btw its 95 model, so im suppose to have that freak ecu? heh.

The purple graph seems to be running preety straight 12 a/f ratio which took abit of tuning on my power fc to get on my tune. The stock ecu would be down in the 10 amd 9 a/f ratio on boost.

Your car was dynoed at the place around the corner from ice, MK as the dyno graph shows. It apparently has the same dyno as racepace.

Those numbers seem pretty right, i got a peak of 178rwkw at Race Pace, running at least 12psi, before dropping off to 10psi. I only had SAFC, exhaust, standard air-box and bleed.

I personally witnessed it.

Though, i beleive all dynos have a descrepancy, could be minimal, but most do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...