Jump to content
SAU Community

Recommended Posts

R32 GTSt RB25DET 5Sp Box Upgrade Setup Complete $1650

Contact me via PM or on this thread. 

Bought these items to suit the extra horses that was supposed to be produced but after many failed attempts and plenty of cash splashed at this project (1 Built Engine [w/ Cams, Injectors & HKS 2835ProS] & 1 Standard engine [w/ Same Inj & HKS 2535] both Turbos dying in the process {Overboost & Oil Issues}) its time to let it all go as im now only going to put in a bone stock RB25DET Setup and itll be a daily and wont be thrashed as much as previously anticipated. So now putting my original RB20Det Box & Shaft in...    

Would Prefer to Sell complete but will Separate if Tailshaft & Speedo Drive Sells First...

Take Complete setup for $1650 or will separate as per below...

Pick up Prefered but will Organize shipping @ Buyer pays freight.

1.) 1998 Model 40th Anniversary R33 Box Off Half cut From SSS w/63000kms on the odometer then put $160 Worth of Redline Gear Oil in it. Comes with Shifter, R32 Mount, Clutch Fork & Thrust Bearing. Sat Behind a Brand New Nismo Coppermix Clutch & Lightweight Flywheel Combo for less than 1000kms   

2.) Nismo Speedo Drive to Suit R32 Manual Speedo Cable (Not a modified Navara Drive) Sourced From USA as Per Pics 

3.) 1Pc Solid 3" Tailshaft With Hardie Spcier Uni Joints, Custom Made to Suit RB25 5 Speed in R32 GTSt 2 Dr (Rebalanced before installed in my car just over a year ago) 

4.) RB30E 5 Spd Box (Equivalent to RB20DET) W/ Shifter & Fork

Bought as back up before deciding to upgrade to RB25 Engine & Box Combo.

5.) R32 GTR N1 Passensger Headlight

1.) $1300 R33 5 Speed 

2.) $170 Speedo Drive

3.) $450 Tailshaft

4.) $200ono RB30E 5 Spd (Equivalent to RB20DET Box) Complete w/ Shifter, Fork & Thrust Bearing 

5.) $150 N1 Headlight Passenger Side

25 Box & 1 Piece Shaft on the Right

605e7a9f.jpg

25 Box & 1 Piece Shaft on the Top

4d3ddad8.jpg

25 Box & 1 Piece Shaft on the Top

13433e44.jpg

25 Box & 1 Piece Shaft on the Left

f01f246c.jpg

Speedo Drive

5088844d.jpg

RB30E Box Far Right

b09da594.jpg

N1 Headlight Top

cceb4559.jpg

Edited by krayzie32

Hi Mate

I need item 2 you listed and was wondering if you would part that out and for how much?

It would be greatly appreciated if you can let me know where you got it from in the states if you wont part it out.

Hi Mate

I need item 2 you listed and was wondering if you would part that out and for how much?

It would be greatly appreciated if you can let me know where you got it from in the states if you wont part it out.

Hi Mate

Made reply to your PM.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...