Jump to content
SAU Community

Recommended Posts

R32 GTSt RB25DET 5Sp Box Upgrade Setup Complete $1650

Contact me via PM or on this thread. 

Bought these items to suit the extra horses that was supposed to be produced but after many failed attempts and plenty of cash splashed at this project (1 Built Engine [w/ Cams, Injectors & HKS 2835ProS] & 1 Standard engine [w/ Same Inj & HKS 2535] both Turbos dying in the process {Overboost & Oil Issues}) its time to let it all go as im now only going to put in a bone stock RB25DET Setup and itll be a daily and wont be thrashed as much as previously anticipated. So now putting my original RB20Det Box & Shaft in...    

Would Prefer to Sell complete but will Separate if Tailshaft & Speedo Drive Sells First...

Take Complete setup for $1650 or will separate as per below...

Pick up Prefered but will Organize shipping @ Buyer pays freight.

1.) 1998 Model 40th Anniversary R33 Box Off Half cut From SSS w/63000kms on the odometer then put $160 Worth of Redline Gear Oil in it. Comes with Shifter, R32 Mount, Clutch Fork & Thrust Bearing. Sat Behind a Brand New Nismo Coppermix Clutch & Lightweight Flywheel Combo for less than 1000kms   

2.) Nismo Speedo Drive to Suit R32 Manual Speedo Cable (Not a modified Navara Drive) Sourced From USA as Per Pics 

3.) 1Pc Solid 3" Tailshaft With Hardie Spcier Uni Joints, Custom Made to Suit RB25 5 Speed in R32 GTSt 2 Dr (Rebalanced before installed in my car just over a year ago) 

4.) RB30E 5 Spd Box (Equivalent to RB20DET) W/ Shifter & Fork

Bought as back up before deciding to upgrade to RB25 Engine & Box Combo.

5.) R32 GTR N1 Passensger Headlight

1.) $1300 R33 5 Speed 

2.) $170 Speedo Drive

3.) $450 Tailshaft

4.) $200ono RB30E 5 Spd (Equivalent to RB20DET Box) Complete w/ Shifter, Fork & Thrust Bearing 

5.) $150 N1 Headlight Passenger Side

25 Box & 1 Piece Shaft on the Right

605e7a9f.jpg

25 Box & 1 Piece Shaft on the Top

4d3ddad8.jpg

25 Box & 1 Piece Shaft on the Top

13433e44.jpg

25 Box & 1 Piece Shaft on the Left

f01f246c.jpg

Speedo Drive

5088844d.jpg

RB30E Box Far Right

b09da594.jpg

N1 Headlight Top

cceb4559.jpg

Edited by krayzie32

Hi Mate

I need item 2 you listed and was wondering if you would part that out and for how much?

It would be greatly appreciated if you can let me know where you got it from in the states if you wont part it out.

Hi Mate

I need item 2 you listed and was wondering if you would part that out and for how much?

It would be greatly appreciated if you can let me know where you got it from in the states if you wont part it out.

Hi Mate

Made reply to your PM.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...