Jump to content
SAU Community

Recommended Posts

Hi sydney kid...I have a sandblast cabinet so i blasted them with glass beads first then they were polished to a mirror finish...next the surface must be free from all polish and foreign matter(its extremely important...more so than with other paints as this paint is transparent and if you get fish eyes or silicon spots then you have to start again)The paint is 2k and must be painted in a completly dust free enviroment as any dust or crap in the paint will show up and a big black spot( this is due to the candy gathering around a speck of dust..therefore a darker patch in that area)The heavier the material is applied....the darker it becomes as i said in the above post,very shapey parts are very difficult to get the surface looking uniform.The part should then be baked at approx 80 degrees....obviously its not spray can material...its a 2K product by a japanese company called ROCK the colour available are very wide from blue purple gold green red and can be mixed to acheive a custom colour........Its important to use the correct material as normal candy will not stick to the polished surface,i guess some adhesion promoter may make it stick but i am unsure on how this would affect the finish......I am quite sure this is the product that Nissan used on there 34 GTR engines from that factory as when i blasted it off there was no primer or nothing under the original paintwork,I remember i painted some R34 covers for a 34 that was repaired when i was in japan and 99 percenet sure its the same stuff i got from the nissan dealer........the covers could have been painted over the original finish but a inferior finish would be acheived

Hope that helps

I still have some material left if you need a set done

Link to comment
https://www.sau.com.au/forums/topic/34738-anodizing/page/2/#findComment-695556
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Hi ylwgtr2, no problem with sand blasting we have a cabinet. Polishing I'm not so sure about whether it is worth the time. What happens if you paint it onto a freshly blasted, clean surface, rather than a polished surface?

Thanks for the offer, but I don't think I could pay for the time it must take. I might be able to justify a swap though, anything you need?

Link to comment
https://www.sau.com.au/forums/topic/34738-anodizing/page/2/#findComment-695570
Share on other sites

id say you will end up with a finished product like the 34 RB26 engine...the polishing is definately the way to go...but horses for courses i guess......i dont really need anything at the moment but an IOU would be accepted :)

Link to comment
https://www.sau.com.au/forums/topic/34738-anodizing/page/2/#findComment-695576
Share on other sites

i have machined a bit of titanium in the past....i cant say i remember it being gunmetal grey :S

I'm an Aircraft Maintainance Engineer by trade, and I have seen many titanium parts. The guy sitting beside me right now (laughing, by the way) used to mandrel bend titanium tube for aircraft, and the colour we chose was the closest to raw titanium that we could find. Freshly machined titanium has a brighter finish though, and I assume that is what you are talking about.

Regardless, the customer was extremely happy with the result, and that's what counts. :D

Link to comment
https://www.sau.com.au/forums/topic/34738-anodizing/page/2/#findComment-696696
Share on other sites

That's a beautiful colour for piping... Your customer has better taste than you do, "Bling Bling Mark" :D

Hey dude, I said I prefered it to the polished look. We were a little uncertain of how it would look, but after I fitted it up we couldn't believe how nice and clean it turned out.

Link to comment
https://www.sau.com.au/forums/topic/34738-anodizing/page/2/#findComment-696725
Share on other sites

Hey dude, I said I prefered it to the polished look. We were a little uncertain of how it would look, but after I fitted it up we couldn't believe how nice and clean it turned out.

DOH!!! I thought you said you prefered the polished look :D

Okay okay, you have good taste too :D

Link to comment
https://www.sau.com.au/forums/topic/34738-anodizing/page/2/#findComment-696736
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...