Jump to content
SAU Community

Recommended Posts

Yeah have had a few make that much on a single 044. The fuel pump isn't the only piece in the puzzle though. Make sure you go slightly overkill on the injectors and make sure the tuner knows what he's doing. I recommend EFI Performance for tuning. Sean there is a tuning god second to none

hmmm... i have a nismo intank pump in my car at the moment and i'm making 285rwkw pulp and 325rwkw on e85...

injuectors are nismo 555cc

i have an 044 and surge tank setup in my ke70 that i'm stripping and was thinking of moving it to the 33... would this flow enough?

Lots of factors, the lower pressure the pump is pushing against the more it can flow. Bosch and other fuel pump manufacturers have charts of this. Ways to lower fuel pressure, ensure your injectors are large enough so the fuel pressure doesnt need to be raised, run lower boost pressure etc

hmmm... i have a nismo intank pump in my car at the moment and i'm making 285rwkw pulp and 325rwkw on e85...

injuectors are nismo 555cc

i have an 044 and surge tank setup in my ke70 that i'm stripping and was thinking of moving it to the 33... would this flow enough?

The nismo pump flows more than the 044. Not sure. The only way to know for sure is to calculate the fuel usage by knowing how many ms your injectors are open for at their peak value in the tune you have. So basically if you can tell me what the largest ms value is in your tune, then I can tell you how many L/min of fuel you are using.

Your engine will consume more E85 than it will 98 so the pump will have to flow nearly double to achieve the same power.

i really wanted first hand opinions not hear say.

seems like theirs a lot of hear say in here :(

As has been said in many of the posts there are a lot of different factors.

If you want first hand opinions get off your butt and go read the dyno threads for 30+ pages of 'first hand opinions' at least 50% of which will have the 044 fuel pump.

As has been said in many of the posts there are a lot of different factors.

If you want first hand opinions get off your butt and go read the dyno threads for 30+ pages of 'first hand opinions' at least 50% of which will have the 044 fuel pump.

Well said

i really wanted first hand opinions not hear say.

seems like theirs a lot of hear say in here :(

We build these cars day in and day out. Some make more than others, some where the customer supplies shit injectors or whatever. Every car is different. You are only EVER going to get estimation when it comes to this sort of stuff. If you plan on making more than 450hp at the wheels on 98, consider a better fuel pump like the Pierburg which flows 6.5L/min

The nismo pump flows more than the 044. Not sure. The only way to know for sure is to calculate the fuel usage by knowing how many ms your injectors are open for at their peak value in the tune you have. So basically if you can tell me what the largest ms value is in your tune, then I can tell you how many L/min of fuel you are using.

Your engine will consume more E85 than it will 98 so the pump will have to flow nearly double to achieve the same power.

thanx dan... ill check it out

I hear what you're saying...

champagne comedy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...