Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

try tipping ice water on the c.a.s when car wont start ( a racq driver told me to do this my falcon )

Common in Fords and Holdens when hot weather and hot motor as the metal in the engine speed sensors 'warp' so to speak in the heat.

Not common for nissans.

Yup I wasn't sure about the external ignitor being on R34s, seems it was indeed ditched for individual ignitors in each coilpack

On that note, try running without the coilpack cover on

  • 2 months later...

Was searching for solutions to this when I found this thread as I have the same issue...

In my case the doesn't really like starting even when cold, but it does start, but is hesitant to do so. I have had it start when warm but it's pretty inconsistent. Inconsistent enough for me to carry a can of start ya bastard in the glovebox.

This is not an ideal solution..

Have replaced Battery (brand new), brand new spark plugs, coil packs (splitfires)

Same as OP.. just sits there turning over forever (or until battery dies), for example BEFORE I bought a new battery, I had someone jump start this car with their car, and a battery pack thing, and I believe the car turned over after about the 150th attempt.

So it starts with start ya bastard?

That tells me there is a fuel supply issue

Yeah, it starts with a quick spray.. 100% of the time, at least the... handful.. of times I've tried it.

I guess that makes sense also given almost everything else is ruled out.. also I suppose it starting when cold, i.e running richer due to.. it being cold and trying to warm up. That said, it's effectively a brand new Bosch 040, that is certainly pumping fuel fairly happily every other time..

Injectors are literally brand new, have done about 100kms. Believe this issue occured (ONCE, while jump starting the car, before new battery too) before they were put in.

For what its worth, car did this.. this morning, at 6am, when it was about 10C outside. I guess it just seems to happen more when warm. If I had to guess, I'd say it just won't kick over about.. 20-25% of the time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...