Jump to content
SAU Community

Recommended Posts

R34 PARTS...THE BODY IS AT THE SCRAP YARD AND THIS IS WHAT'S LEFT

OPEN TO OFFER BECAUSE I WANNA CLEAR THE YARD WILL SWAP PARTS I HAVE FOR SALE

FOR THE ITEM'S LISTED AT THE BOTTOM OF THE PAGE.

>DUMP PIPE (ADVANCED) $80

>AIR BAR STEERING WHEEL $150(MANUAL)

>DRIVERSIDE DOOR WITH GLASS $250

>DRIVERSIDE MIRROR $50

>REAR WINDOW (REMOVED) $150

>DRIVERS DOOR TRIM $100 (HAS WINDOW SWITCH STILL)

>R34 STOCK AIR BOX DAMAGED $50 (ONE CORNER & ONE TAB)$50

>A/C COMPRESSER $100

>A/C CONDENSER $50

>ABS MODULE $100

>BRAKE MASTER $150

>DIFF $200

>REAR BRAKES COMPLETE $400 AS IN PIC)

(lower control arm is bent on one side)

>TAILSHARFT $100

>CLUTCH MASTER $50

>PEDALS $100

>HAND BRAKE HANDLE $50(WITH FRONT CABLE)

>STOCK STRUT BRACE FRONT $25

>IGNITION BARRAL/DOOR/BOOT LOCKS AND A KEY $100

>R34 FRONT CROSSMEMBER $150

>BONNET CABLE/LATCH AND HORN PEICE $50

>R34 CASTOR RODS STOCK $50PAIR

>SR20DET 5 SPEED GEARBOX GOOD CONDITION $350

>HIGH FLOW CAT $100

>Vertex Body Kit to suit lancer 96-03 Coupe (full kit) $500

>DECAT PIPE $50

AND THESE ARE THE ARTS I NEED AND AM WILLING TO SWAP PARTS PLUS CASH FOR THEM..OR IF YOU HAE THESE PARTS CHEAP PM ME.

SR20DET RED TOP/S13 SILVIA

1.GREDDY PULLEY KIT (MOST IMPORTANT AND URGENT)

2.GREDDY/HKS CAMS

3.HKS FUEL RAIL

4.NISMO FPR

5.550CC INJECTORS

6.S13 BN BODY KIT......FRONT / SIDES / REAR

Link to comment
https://www.sau.com.au/forums/topic/349323-r34-parts/
Share on other sites

  • 1 month later...

Hey buddy, im after some parts for an R34, here's a link to what i need so if u have them do let me know.. -> http://www.skylinesaustralia.com/forums/topic/355141-r34-gtt-rear-seat-belt-and-front-indicator-holder/

Cheers

Link to comment
https://www.sau.com.au/forums/topic/349323-r34-parts/#findComment-5694622
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...