Jump to content
SAU Community

Recommended Posts

Instead of modifying the RB25 one will the RB30 E one fit with the 25 pump, I would rather a straight swap over trying to modify the one on it, my problem is the 5 mm offset that is causing the power steering belt to come of at high RPM.

And I did search but only found that a RB30E bracket might fit.

Thanks, Mark

Link to comment
https://www.sau.com.au/forums/topic/349714-powersteering-bracket/
Share on other sites

i just use the rb25 one i think. unmodified. just had to put spacers between the bracket and the block on two or the three mounting points. from memory this was only because the aircon pump bracket used to go between the block and the powersteer pump bracket on the rb25. so now that i dont run the aircon bracket on the 30 i needed to chuck about 30 mm of spacer in on two of the bolts.

*i think* lol.

cant remember exactly but i'm pretty sure the only different is the one bolt hole. i compared a 30e and 25 bracket when doing the conversion and thats the only difference i noticed. went from using the 25 bracket on the 25 to the 30e bracket on the 30det with no dramas, re used the old belt and its never come off.

Edited by JonnoHR31

Sadly the RB30 bracket will not accept the 25 pump and the top bolt hole also doesnt line up with the 25 head anyway, UNIGROUP are making a bracket up now so all is well.

Modified = good-Standard = bad

Thanks, Mark

On the rb26, the top bolt hole doesn't line up because on the 2.6 motor the top bolt is in the cylinder head, and on the 3.0 it's in the block. Pretty sure it's the same for the 2.5.

The RB30 bracket has all the mounting bosses at the same depth, but on the 2.6 the top hole has a thicker casting. I tried to use the rb30 bracket, but it sits the pump too far back.

Easy solution is to just hacksaw off the excess material from the 2.6 bracket, the cast iron is pretty soft and it's not difficult or time consuming to get a nice cut that sits everthing neatly and then you know you're belt lines up straight. I haven't had any problems with mine after 2000 kms.

My 2c.

On the rb26, the top bolt hole doesn't line up because on the 2.6 motor the top bolt is in the cylinder head, and on the 3.0 it's in the block. Pretty sure it's the same for the 2.5.

The RB30 bracket has all the mounting bosses at the same depth, but on the 2.6 the top hole has a thicker casting. I tried to use the rb30 bracket, but it sits the pump too far back.

Easy solution is to just hacksaw off the excess material from the 2.6 bracket, the cast iron is pretty soft and it's not difficult or time consuming to get a nice cut that sits everthing neatly and then you know you're belt lines up straight. I haven't had any problems with mine after 2000 kms.

My 2c.

My main problem apart from the top bolt which would need some fab work is the pump has different adjustment points, the 25 had a threaded rod where the 30 uses a slot in the bracket so I would need to swap from the 25 pump to a 30 pump, Its going to be much cheaper to fab up a plate and use the 25 bracket instead of replacing the whole set up.

Mark.

use the 25 pump on the 25 bracket on he 30 block. and yer ur on the money, i went to use 30 bracket but the 25 pump wouldnt fit the 3 litre bracket so i used the 25 bracket and spaced it out im pretty sure.

A bracket was made to join the lower fixture points and the top fixing point on the bracket was milled out to allow it to move forward about 3mm so that the H/balencer and P/steering pump idlers line up.

She revs to 7.2k now without throwing the belt onto the under tray, WIN.

  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

either use the 30 bracket or cut the excess off the top lug of the 25 bracket. easy

If youve got the 30 pump thats fine but if your using the 25 one you need to mod the bracket at the bottom with a plate and remove 5 mm from the rear of the top hole to allow the pump to move forward 5 mm.

The 26 pump/bracket is different again Im told.

Mark

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...