Jump to content
SAU Community

For Sale Garrett Gt3076R Direct Bolt On R33

stealthfoz
 Share

Recommended Posts

stealthfoz Enthusiast

stealthfoz

Posted
Posted (edited)

garret gt3076r

BALL BEARING 60 TRIM COMPRESSOR

59.8mm Inducer / 76mm Exducer (Compressor)

60mm Exducer / 54.8mm Inducer (Turbine)

Internal gated rear housing

CHRA PART NUMBER 700177-13

DIRECT BOLT ON TO RB20 OR RB25DET WITH STANDARD 6 BOLT EXHAUST FLANGE

$800

Edited by stealthfoz
  • Like 1
stealthfoz Enthusiast

stealthfoz

Posted
  • Author
Posted

how long have u had it for? and what power were u making and what psi?

had it about 1 month and have only fitted it but havent had car running

and the power output comes from more factors than just the turbo and boost.

it is a 450hp turbo

stealthfoz Enthusiast

stealthfoz

Posted
  • Author
Posted

it is still fitted to car. i can only take pics with it fitted and mms them to you. i am not removing it until its sold as i will keep it if it wont sell. as it only takes an hour to remove i will remove once payment has been made.

turbo only.

stealthfoz Enthusiast

stealthfoz

Posted
  • Author
Posted

as posted above i have a couple of shitty pics of it on the car but i wont remove until its sold as i will keep it.

i can mms pics of it installed if you send ph number..

there is heaps of interest but noone with cash.

so i dont want to waste my time removing if noone comes up with cash

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...