Jump to content
SAU Community

Recommended Posts

i know if i pull something the gtr becomes rear wheel so does that mean i can drift and how good does a gtr drift compare to a silvia because i have all those mods like oil cooler , suspension and roll cage that i dont want to go to waste when changing cars so i hope i can keep my gtr and drift as well

thanks

Link to comment
https://www.sau.com.au/forums/topic/35191-gtr-drifting/
Share on other sites

pull the 4 wheel drive fuse in the engine bay and youll drift all day and night, and next day amd week after and beter then any silvia, i dont even know why people waste their time drifting in sylvias. :flamed: :wassup:

Link to comment
https://www.sau.com.au/forums/topic/35191-gtr-drifting/#findComment-703161
Share on other sites

R32 GTRs weigh 1470kg, as opposed to a Silvia which is 1100kg from memory. Whilst the suspension and general design of the chassis of these vehicles is very similar, the Silvia is a much better choice for drifting due to the light weight and easy induced oversteer behaviour. For circuit racing however, its a whole different kettle of fish, when ATTESA is introduced.

This is not to say that you cant use a GTR for drift, it just isnt its ideal use. Much better than a HSV anyday...

R32 GTRs can just have the fuse pulled for slip and slide, not so easy in R33s however.

Link to comment
https://www.sau.com.au/forums/topic/35191-gtr-drifting/#findComment-705051
Share on other sites

Guest INASNT
32 GTR is just a matter of pulling a fuse or setting up a switch in cabin

33 GTR i am not 100% sure but i think the later ones need the shaft pulled out

In a 32 GTR yes u can pull the fuse to get it into rwd mode, but if u intend to drive all day in rwd mode u need to take the front shaft out otherwise u will burn out the transfer case.

Link to comment
https://www.sau.com.au/forums/topic/35191-gtr-drifting/#findComment-708487
Share on other sites

r32 takes 2 fuses to get into RWD, 1 under bonnet 1 in cabin... you can also get it into rear wheel drive by turning the car off and then on again while moving.... but as soon as you come to a complete stop the 4WD will re-engage.... by the way when you do both of these you also disable the ABS... :rofl: a fun and happy drifting...

Link to comment
https://www.sau.com.au/forums/topic/35191-gtr-drifting/#findComment-710771
Share on other sites

Its because the GTRs 4wd ATTESA system is electronically controlled. When the computer senses the rears loose traction it can send up to half the torque to the fronts. If you remove the fuse or install an inline switch etc, it will become rear driven only.

Some1 tell me tho, how hard is drift on a GTRs CVs? Because we all know how cheap our jap parts are...

^ I made that all up. But i think its close... ^

Link to comment
https://www.sau.com.au/forums/topic/35191-gtr-drifting/#findComment-719660
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...