Jump to content
SAU Community

Recommended Posts

Up for sale is a set of R33 GTR sway bars.

I bought these off bubba a while back and they don't fit my car(Auto)

They will fit manual C34 series 1 or 2 stagea.

(please dont turn this into an argument about what swaybars fit what car)

the rear is 22 or 24mm solid from memory, a great upgrade over the standard 17mm hollow bar.

Selling them for less than i paid for them.

Rear sway bar comes with rubbers, u bolts and links to suit.

$150 + postage

Located south of Adelaide

Pm or call me - 0423 10 11 10

stock rear sway bar compared to r33GTR sway bar

DSC01091.jpg

They will fit manual C34 series 1 or 2 stagea.

(please dont turn this into an argument about what swaybars fit what car)

Firstly I'm genuinely interested in this item.... However Im unsure as to if these will fit my car, why doesn't it fit your auto? Whats different from the auto and manual rear sway bars.

Also for the record RS4's were NEVER sold in a manual.

Firstly I'm genuinely interested in this item.... However Im unsure as to if these will fit my car, why doesn't it fit your auto? Whats different from the auto and manual rear sway bars.

Also for the record RS4's were NEVER sold in a manual.

it's all about that rear cradle and the extra width that the autos have. i have heard of people putting the sway bar links on mad angles and this didn't really worry me but on my car i couldn't get the u bolts in.

When i bolt one side on, the other side was a full bolt hole off, if you were to bolt them up like this, the rubbers would be sitting on the corners of the sway bar, not the straight section.

Anyone is more than welcome to come and put there car on my hoist and have a look, if you think you can make it work and deal with the link angles, you are more than welcome to buy them

p.s whats with the random rs4 fact??

Edited by Big Fella

looking at my mates rs4s his rear sway bar was only 19mm, so it would be an upgrade for sure.

Just measured the 33 gtr sway bars

front is 22mm solid

rear is 27mm solid

here is the issue for auto stageas, the right side is bolted up and the lsft hand side is way off.

the right side is shwon here, right on the edge of the straight section

DSC01187.jpg

and this is how far off the left side is

DSC01188.jpg

i was planning to make a 5mm thick plate for each side, with 2 threaded holes and thru holes to mount it up, but i've run out of time and motivation

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...