Jump to content
SAU Community

Recommended Posts

Im having troubles with my s1 r33 when i stand on the accelerator it reacts normaly but when it changes to second gear the revs fall to 3k and wont accelerate any more.... could it be a form of limp mode...

also when it changes from 1st to second... before it cut the revs it would hit limiter for a second before it pulled second... not shure if this in normal...

Link to comment
https://www.sau.com.au/forums/topic/352373-auto-doin-weird-shit/
Share on other sites

have you checked your oil in the trans.

Whens the last time you've done a service on it?

is there a trans oil cooler? sometimes in the hot weather it decides to overheat and the trans becomes noticably sluggish.

and judging by your trans flaring between 1st and second,it sounds like your 2nd gear clutch plate is completely worn. Looks like a rebuild mate.. or a manual conversion!

If your doing a trans oil change, make sure to ONLY put whats on the dipstick, or a fully synthetic oil like nulon AT Tran fluid. I'm pretty sure 33's runs Re5 4spds?

Edited by AaronNM35

Yer mate could be a rebuild... it was serviced with new oil like last month... arnt those gearboxes electronicly controlled could it have somthing to do with the TPS because the way it cuts the revs is super weird... and if its worn meh ill just drive it till it pisses me off lol its only a daily i have a track car to go fast...

yeh there is a trans ecu talking to your Main ECU.

so if it notices a fault in the trans it can actually talk to your main ecu telling it basically not to rev so hard so it can avoid the trans slipping.

when they did the service they may have used Dextron III which isn't the best fluid for an RE5 trans. it needs to be what on the dipstick., or basically goodbye transmission.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...