Jump to content
SAU Community

Recommended Posts

hey people, done a quick search but couldnt really find anything,

is anyone using the cooling pro r33 ally radiator in there s1??

i know i will have to use an auto cooler thats not a drama but really want peoples opinion on fitment, size and if the shroud actually fits!

thanks people!!

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/
Share on other sites

You need a AUTO specific rad with the bottom tank setup for auto trans fluid. That bottom tank isnt their to "cool" the fluid its their to get it up to temp and keep it at as much of a consistent temp as possible..

I have heard that before. So why have a tranny cooler??? >_<

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651040
Share on other sites

I have heard that before. So why have a tranny cooler??? pinch.gif

Not trying to sound smart, but there seems to be a bit of confusion surrounding trans coolers and their use; hopefully this helps.

The thing in the bottom tank is a heat EXCHANGER; not specifically a cooler or heater.

If the water is hotter than the trans fluid; heat will be transferred to the fluid, if the fluid is hotter than the water; heat will be transferred to the water.

Under duress, the trans transfers a decent amount heat into the trans fluid, it can easily go over 100 deg in the right conditions.

The heat exchanger in the radiator is usually nothing more than a simple copper or aluminium tank, no fins for extra surface area. They are not particularly efficient.

So in extreme conditions with high water temp, using a dedicated trans cooler is much more effective at stripping that heat out of the fluid, making life easier for the gearbox.

Also, ambient temp is always going to be lower than the temp of the water in the cooling system.

A side benefit is reduced load on the cooling system.

Running the fluid throught the radiator mounted exchanger, in addition to an external cooler just ensures the trans fluid will be around the same temp as the radiator water, not ambient temp in cold conditions; as Pipster & Kidafa have said.

Edited by Daleo
Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651186
Share on other sites

i dont understand either, the auto-trans specialists up the road from my work say built in radiator trans coolers are rubbish. and then why do people fit large external trans coolers for "towing/extreme condition/high perfomance applications" ? also read an article in a 4X4 mag that said the higher your auto fluid temps the shorter your auto trans life and it had a graph with "auto fluid temp" over 'hours of life".

all autos will be sluggish when cold regardless of 'heated' or external cooler. My x-trail i just sold (my07) had a built in cooler and i fitted an external cooler and it drove the same, had long drawn out gear changes for the first 5 mins of driving til the trans fluid got up to temp, the external cooler didnt take any longer or shorter to heat up than the built in one.

personally i would run the cooling pro manual stagea 3 core radiator, a moderate size external tranny cooler and a top quality trans fluid.

also as chuckie mentioned, use the search function and there is a billion radiator and tranny cooler threads

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651192
Share on other sites

if i did it again, i'd get one of the asi radiators from ebay

same quality as cooling pro (ok for china) but about $100 cheaper

oh, and i read about the auto heat exchanger, you only need it in cool temps or your fluid will not warm up if you have an external cooler

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651263
Share on other sites

yeh like if you live -20 degree conditions in the middle of the day you would need it, i believe now some german cars have electric elements in the engine oil sump to heat the oil so its easier to crank when cold?

In some sub arctic countries, rather than heat a garage, they do exactly this, just need to remember to plug your car into the power point before going to bed.

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5652579
Share on other sites

In some sub arctic countries, rather than heat a garage, they do exactly this, just need to remember to plug your car into the power point before going to bed.

my aunt in canada has had that for years

also means that the heater blows hot air as soon as it turns on

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5652862
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...