Jump to content
SAU Community

Recommended Posts

for sale

rb26 with a jun 2.7l stroker this engine done 300kms making 400kw on 20psi boost@8000 during these kms the limiter has been set at 8000rpm i want more torque so im going a rb30 this engine will not have water pump, oil pump no top end,sump there was no expense spared on this engine cost me alot more money and time to build $12000

rb26 this engine has been machined bored,honed and balanced has 87mmcp forged pistons,rods have been prepped and balanced has a r33 crank which is balanced with everything else comes with n1 oil,water pump the head has been shimed and overhauled and comes with 264 hks cams,hks cam gears has the gasket kit,bearings. everything that is needed to rebuild this engine is there and its new $10000 can arrange for a very well known builder to assemble

hks rs turbos these where on the car when i bought it so i dont have the history of them they are still on the car so they work perfectly they are making the power that is listed up top comes with manifolds that have been ceramicoated but has no actuators also the turbos have been ceramicoated as well compressor cover and exhaust snail $3000

if want to see if engine is anygood its still in car can hear running

PLEASE NO TIME WASTERS IM NOT VERY PATIENT WITH TIME WASTERS

Link to comment
https://www.sau.com.au/forums/topic/352833-jun27rb26hks-rs-turbos/
Share on other sites

for sale

rb26 with a jun 2.7l stroker this engine done 300kms making 400kw on 20psi boost@8000 during these kms the limiter has been set at 8000rpm i want more torque so im going a rb30 this engine will not have water pump, oil pump no top end,sump there was no expense spared on this engine cost me alot more money and time to build $12000

rb26 this engine has been machined bored,honed and balanced has 87mmcp forged pistons,rods have been prepped and balanced has a r33 crank which is balanced with everything else comes with n1 oil,water pump the head has been shimed and overhauled and comes with 264 hks cams,hks cam gears has the gasket kit,bearings. everything that is needed to rebuild this engine is there and its new $10000 can arrange for a very well known builder to assemble

hks rs turbos these where on the car when i bought it so i dont have the history of them they are still on the car so they work perfectly they are making the power that is listed up top comes with manifolds that have been ceramicoated but has no actuators also the turbos have been ceramicoated as well compressor cover and exhaust snail $3000

if want to see if engine is anygood its still in car can hear running

PLEASE NO TIME WASTERS IM NOT VERY PATIENT WITH TIME WASTERS

I'm not quite sure what you are selling?

An RB26 with june 2.7 kit? but no top end, oil or water pump or/and an RB26 with an oil and water pump?

Interested in the 2.7 kit engine, but would need to know a hell of a lot more information.

selling both mate

what do u need to know bout 2.7 its a 05u block that has been bored out to 87mm it has a jun 2.7litre stroker kit in it and was assembled by paul diemar red r racing engine is in car so compression can be done has no oil/water pump, harmonic balancer in the sale

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...