Jump to content
SAU Community

Recommended Posts

phew ..... lucky outcome actually. Surprised valves didnt smash themselves to pieces.

glad you got out of it in the end.

Question : how many kms has the car done? was the stuffed belt in bad/worn condition or was it the bearings fault?

AFAIK the prob was a seized bearing in the idler pulley. From what I saw, the inlet side has hopped six teeth, the exhaust side only one tooth. A new belt was fitted and the car started OK and was driven out to be fixed tomorrow when the new kit arrives. It is all very perplexing caus all the other threads I have read on this subject have reported severe internal bleeding. It must be remembered that the T/B did not break. It was partially laminated. I can only surmise that the ecu detected an abnormality in the "what?", and went into limp before any serious damage occurred.

Thank you Mr. Nissan.

I am off to the Newsagent tomorrow to get that winning ticket. Thanks Duncan. :thanks:

phew ..... lucky outcome actually. Surprised valves didnt smash themselves to pieces.

glad you got out of it in the end.

Question : how many kms has the car done? was the stuffed belt in bad/worn condition or was it the bearings fault?

[/quote

The belt had been replaced at 105ks. Was a Gates. The belt was OK on the tooth side. The outside was laminated due to the seized bearing in the idler pulley.

Moral: When replacing the belt, replace the pulleys.

ahh there you go :D moving a few teeth is totally different to snapping entirely where the crank and valves can move independantly.

SR cams or not, surely the de motors have higher compression and therefore pistons protrude further into the valve area?

And yes.....always replace the idler and tensioner! This is far from the only motor this has happened to over the years :( Also, importantly, replace the stud that the tensioner attaches to, and the bolt that the idler uses, they can also break, particularly if poorly tensioned at some time in their history

phew ..... lucky outcome actually. Surprised valves didnt smash themselves to pieces.

glad you got out of it in the end.

Question : how many kms has the car done? was the stuffed belt in bad/worn condition or was it the bearings fault?

its always advised to do the tentioners when u do ur timing belt so what happend dosent most people are to cheep but it certainly pays off

having bearings, belts etc being replaced on the rb26 atm - track duties 3x per year only but no point playing Russian roulette

then again, also replacing rod bearings at same time, crankshaft being machined, oil return system, etc :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
    • To re-cap, I bought: https://www.alibaba.com/product-detail/Lsailt-8G-Infiniti-Q50-Q60-2014_1601171829627.html?spm=a2756.trade-list-buyer.0.0.2cd476e9FTIlKE As you can see, if I bought 20 it was $653, but I bought 1 so it was $1,170. I was very tempted to buy 2 and resell 1 at 25% cheaper. @MBS206, I am not sure if they do a Kluger one, here is their list but it might be there under a global model name: http://www.lsailt.com/product/android-interface?page=1 Keep in mind these full android replacements have basically all the bits a phone does (cpu, ram, storage, wifi, bluetooth, usb interfaces) other than a screen (it uses a host), thus the $800+ cost. Android Auto screen mirroring is MUCH cheaper as it's just a cut down shell, input mirroring and output mirroring BTW I also need that "screen off" feature, it is much harder to see wildlife even if a dash is reasonably dark. Both the Fuga and V37 have display off buttons for night use, they just come back on for a second or 3 if you interact with it, eg skip a song.
    • I use FCC car launcher. It has an option for different backgrounds, so instead of turning the screen off you can swipe 'up' to a black screen with no background/icons. (mine has the time on it only). It's kinda nice. Also lets you use gestures to say swipe to go to next song, etc.  
×
×
  • Create New...