Jump to content
SAU Community

Recommended Posts

Hi. I recently ordered a GTX3071R turbo kit. The supplier has contacted me and said there has been a delay as they received a GTX3076R instead, and that the turbo I ordered would take a couple more days to get in. I told him that was strange as I was actaully split whether to get that turbo in the first place.

I have been thinking recently that I would put in a set of forged pistons and ARP rod bolts while the engine is out (I will use the stock RB25 Neo rods). If I am going to do this to the engine do you think I might as well go for the bigger GTX3076R instead and make use of the stronger bottom end?

I have read the other thread about the new GTX30 series turbos and the concensus seems to be that the new GTX3076R is more like the old GT3582R. The car will predominantly be used on the street with the occasional trip to the drag strip. It has all the supporting mods. Will the GTX3076R be too laggy?

Please help me make descision!! And help is greatly appreciated! :)

Link to comment
https://www.sau.com.au/forums/topic/354118-please-help-me-decide/
Share on other sites

I know there is lots of information available, and I know it is a decision between more power or more lag. I was just hoping for a quick comment or two from someone to help me go one way or the other because I am sitting right in the middle at the moment, and I need to make a quick decision.

Was this thread started as a joke?

there is SO MUCH info about them that it comes down to you, and your decision.

you either want more power and lag, or you don't.

I know there is lots of information available, and I know it is a decision between more power or more lag. I was just hoping for a quick comment or two from someone to help me go one way or the other because I am sitting right in the middle at the moment, and I need to make a quick decision.

get out a coin and flip it as honestly you'll end up with a result that way.

everyone has a different view.

Done and done!! I should have it soon, although the rest of the car is going to take me 2 or 3 months to finish putting it together.

Thanks everyone for the input :)

We need more test pilots, so go for the GTX3071

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...