Jump to content
SAU Community

Recommended Posts

Hey all,

Trying to install a set of QFM pads I bought from a guy here. The back ones were easy. Removed the old, grabbed the old brake pad in the caliper to compress the piston. Slide out and insert new one.

The front is being a bitch. I can't compress it. No matter how hard I squeeze it(using those adjustable plier things). When the pads are in and on the car and someone presses the brake, I can feel them moving, I just cant push them back. Does anyone have any advice? Do these need to be turned or forced?

R33 GTST Series 2.

Link to comment
https://www.sau.com.au/forums/topic/354699-changing-brake-pads-help/
Share on other sites

firstly, be careful!

the piston needs to slide back straight into the caliper. if you try and force it at an angle it might seize. and if you push even harder you might manage to score the bore and damage it permanently.

firstly....clean everything really well with brake cleaner. this will remove as much old brake dust as possible. even scrub lightly around the piston with a nylon brush.

then - before pushing it back, make sure your master cylinder is almost empty. If it is not it will overflow when you push the pistons back.

then, you need to push them back as straight as possible. use something long and wide to lever them downwards like a large spanner or thin hammer. take it slowly and change from side to side to make sure they go evenly. a g clamp is even better it will push them back straight.

I will buy some brake cleaner tomorrow. I don't want to interfere with the hydraulic system as I just recently had my fluid topped and bleed properly.

Can I do one piston at a time or should I do both at once? One at a time I can use a clamp to squeeze each one in. I can squeeze the 2nd brake pad in its just the one that sits on the outer side I cant push in.

they should all retract exactly the same way. if one is much tighter it is probably not straight or already seized.

as you push one piston in all the others will want to move out. you have to push them all together, or hold 3 while you push the other one

I normall leave a brake pad in against the pistons u are pushing on. This helps move them together and keep them square.

Use the adjustable multi grip pliers and squeeze.

If ur brake fluid has recently been topped up then once u push the pistons into the caliper there will be brake fluid all over the firewall. When this happens wash it down immediately with water

f**k finally done with just slightly overflowing the fluid bottle. I used a multi grip, the one with the screw end to adjust bite, and a piece of cardboard wedged between the pad and the rotor to ensure it sits flat as possible and slowly squeeze then adjust the tool to be tighter then squeeze until I fit the other one in.

I cleaned off as much of the gunk as I could and I think that helped.

Cheers guys, now I just need to find the damn retaining clip for the push pins.

Its not the wire part bro its the metal thing which puts tension on the two pins, the flappy piece of metal. I went to a skyline wrecker and he wont sell it to me because he reckons he wont be able to sell the caliper without it lol.

%21B6d%21lowEWk%7E$%28KGrHqF,%21g8EyrpG2ZJEBM%29YR-JeM%21%7E%7E_1.JPG?set_id=8800005007

Its the n parts you can see above NIssan. Where can I get them? Are they essential to have? Would Nissan have them? Ive been driving my car since I bought it, without it lol.

umm that is not ideal, the spring clips hold the pad in the caliper.

I have used r pins for years instead of the wire to hold the pins in, but I've never tried it without the spring clips

well the pins should keep the pads in the caliper ok, but from memory the spring clip works to keep the pads up against the pistons. without them the pads 'might' rattle around a bit on the pins but most likely they'll be ok. personally though I would just call up nissan and buy a pair and stick them in. they are not expensive (maybe $20 for a pair) and easy to put in.

BTW when you were first trying to push the pistons in did you have the cap off the master cylinder? seen plenty of people trying to push pistons in with the cap still on which makes things pretty hard as the system is sealed so there's no room for that pressure to go. eventually the pressure will escape somewhere (usually through the cap) but sometimes it pops post the master cylinder seal etc which is not good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...