Jump to content
SAU Community

Recommended Posts

HI ALL,,,

I have a r33 with RB25, Power Fc with hand controller,

Up untill yesterdy all was fine, not had a prob before with it.. water temp would sit 78 - 80 once fully warned up after (about 5 minutes) and might creep up to 83 after few hours driving,Fine right? been like that for years

Right,

My cars been sitting in the pannelbeaters the last couple months, (front bumper damage and minor side pannel damage) the radiator didnt get touched atall in accident baring in mind, but they had to remove the rad to do work, when i went to the place yesterday car was running, they said it had been running a couple of minutes and i looked at Fc hand controller and Water said 60.... i then revesed straight out of the unit (20ft) got outta car. talked for honestly no more than two minutes, Got back in car and hand controller was reading 114c!! pannelbeater says nah that cant be right because the stock temp gauge is only reading just above halfway mark?

Please all! Am gratefull of all advice!!

CHEERS AGAIN

Link to comment
https://www.sau.com.au/forums/topic/355488-r33-gtst-extrem-over-heating/
Share on other sites

Let it cool Nd check the coolant level. If its ok leave the cap off open the air bleeder screw on the inlet manifold till coolant comes out then refit the bleeder screw and start the car, let it idle till it warms up with cap off and heater on.

This should remove any air that is still trapped in the cooling system.

If it still overheats get a new thermostat

pannelbeater says nah that cant be right because the stock temp gauge is only reading just above halfway mark?

in my experience, the stock temp gauge reaches half-way around 60-65C and will stay there till around 110C before rising - so it could be easily right.

+1 on bleeding the coolant system too.

You may have air in the sysyem, When the car is cool remove the radiator cap and start the car, let the car idle for a while(might take 5-10 minites), giving it a few revs here and there, watch your temp gauge, and add coolant as needed, also ensure you have some coolant in the overflow for when the car cools down so it doesnt suck air back in.

Might fix it.

Mark

in my experience, the stock temp gauge reaches half-way around 60-65C and will stay there till around 110C before rising - so it could be easily right.

+1

Basically from my experience the stock temperature gauge should always be reading just under 1/2 way for a normal operating engine at normal temperature.

If it gets to 1/2 mark then thats enough to throw a caution, anything over 1/2 means there are potential over heating issues with the engine.

I had my gauge read just over 1/2 way & when I pulled over the coolant was boiling in the reserver tank, even though according to the stock gauge it's no where near the H mark, had it checked & it turned out to be a worn Rad cap & thermostat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...