Jump to content
SAU Community

Recommended Posts

I woke up this morning thinking that I've never seen a car race where Power to Weight ratio is a class.

There's power band, engine size, NA, Turbo, Rear wheel, Front wheel classes etc... but I never seen a race where cars are put into classes where Power to Weight is the same or similar. It would open up the track to a much greater variety of cars.

Does it exist? If not, is there a reason?

I have no idea why I woke up with this in my head.

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/
Share on other sites

Power to weight has very little to do with circuit work.

Think Bathurst.

2 Cars both have the same power to weight, 1 has 200hp 1 has 600hp, which do you think will get around to mountain faster?

Curious...what race class has limits on where in the RPM range you can make power? (power band)

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5691469
Share on other sites

OK in that particular track, I would think Torque would come into play, fair call. (Forget that Power Band example.)

But say the track was flat? I would think it would be a close race wouldnt it? Actually when I think about it, I guess it would be a dis-advantage for the 200hp car on the straight. But say use the track at Wakefield. When I last went, the Hondas were eating up the bigger powered cars. I guess it depends on the track aye.

I guess why I was thinking of this was I was watching a Mini-Cup challenge on the weekend that I taped. All cars, identical, only thing that separates the winners and losers are the skill of the driver. But it got boring after a bit watching the same cars drive passed over and over. Would be nice to see a race where different types of cars compete together in a fair way.

I know the GT races are kinda like these but they're all Super Cars. Would like to see something more like the World Time Attack Challenege they had here last year.

Edited by Bourbon Boy
Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5691571
Share on other sites

What you are thinking of is IPRA (improved production) turbo cars need to run inlet air restrictors, there are minimum weights for different cars etc.

The only real bullets in a straight line are the 6L V8 Commodores, but then they are massivly under tyred so are slow through the corners and have to get on the brakes earlier etc

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5691579
Share on other sites

Production sports cars used to run power/weight classes, ie you could choose whatever power and weight you wanted but you would be competing for points against other cars with the same power/weight.

The issue of course is weight is easy to measure and power is not. they used to take a dyno to some rounds and check some cars but it was just too hard to stay on top of. And too easy to fake lower power for a dyno run (eg boost controller or 2 maps on computer).

Tyres are really the best limiting factor IMHO. Keep everyone on the same, cheap, average tyres and lots of other things even out....

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5692225
Share on other sites

control tyres are good - but also racing in a one make class is good cause then while some people have big budgets, others dont and is quite competitive.

Duncan you raced in the Daewoo series hey? so pretty much control everything! comes down to skill!

If I were to race in Prod Sports (which my car is built for) Im up against other 2F cars such as lotus's, rx7's, porka's etc which will suck balls.while in the mx5 class, its good as everyone has a different budget and is fun!

but I still come last. haha

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5692258
Share on other sites

lol you beat a lotus chris, i remember it well :D

building a car to a class is a good idea (I did it :P) but it is not simple, easy or rewarding. It is limiting and frustrating. My GTR must be about the slowest one in the country!

But from when I first decided to build my own car, I knew I could not outspend the competition, so I went looking for tight rules where budget did not automatically determine who wins.

One make racing was excellent, but because it is close it is full of cheats. The Daewoo series was controlled one make so we couldn't even have the cars to fiddle with them - even so there was 10% power difference between the slowest and fastest of the 20 cars. 10% is a mile. The one time I got the quickest car (wakefield 500), Tom, Mark and I were leading by literally 1 lap when the power failed :(

So basically....there is no such thing as a level field, and no category where you don't need a reasonable budget to win.

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5692442
Share on other sites

easy...supersprinting :D where are you based?

NICE! Thanks man. I never knew about this... I googled this: http://www.supersprints.com.au/

Is this what you're talking about?

What do you win? Is it just for glory?

Based in Sydney.

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5694811
Share on other sites

supersprints are good fun and good entry level.

to give you a run down...

A skyline is to go into class SVD.

Its against the clock - but you are in a class.

you dont race for position on track as its not a race,well, more a race against clock and quickest lap wins.

in SVD class, you'll be up against GTR's, EVO's, highly modified commodores and falcons etc - most will be street registered. in fact I think they have to be street registered to be in SVD

My MX5 is 2B which is 1600-200cc and street rego'd with some modifications

There is the CAMS state supersprint series, and there is also the interclub one. I have done a a couple rounds of the CAMS one but 2009 I did the interclub one with southern sporting car club. 2011 I'll hopefulyl do 4 out of the 6 rounds.

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5695102
Share on other sites

I was just reading this: http://www.supersprints.com.au/rules-and-regulations/2011/2011%20Vehicle%20Regs.pdf

There is no SVD? Just an SV and I dont think I'd be in that.

I'd probably be in Type 2 class with my 350GT with only an exhaust, braided brake lines & slotted roters as mods.

There is no entry fee information on the website but I assume that it will be in something like a normal club day out like $200-$300 depending on the track??

Whats minimum spend on entry\rego fees in a SuperSprint Championship series? (Excluding car mods\repairs that is...)

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5695153
Share on other sites

nah your car is SVD. Not type 2.

there are different SV type classes but skylines fall under SVD unless you have an r32 or r35 aussie delivered.

the rules are weird.

entry is anywhere from 180 - 220 and you'll need to hire a timer beacon for 10-20 bucks

no rego fee's for them.

if you want more a relaxed series, the southern sporting car club has 4 at wakie and 2 at EC and isnt as full on as the CAMS state round.

google sscc

cheers!

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5695195
Share on other sites

yep!!

some SVD racers do 1.40's at EC and 1.04's at wakie...

however, go there for the fun and try and beat your PB each time!!

if you are out there for fun (most people are!) who cares what lap times, you are out there enjoying your toy! just make realistic lap time goals and aim for them each time!

if you then get serious and bug has bitten, sell and then buy something that maybe comptetive in another class (like me haha)

Link to comment
https://www.sau.com.au/forums/topic/355510-race-classes/#findComment-5695490
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...