Jump to content
SAU Community

Recommended Posts

Hey, i've got a 2003 skyline v35. a couple of months back when it was about 40 degrees the coolent started to boil and spurted out which created havoc with the air con. ever since every now and a again when i start the car i hear this

water sloshing sound in front of the dashboard. anybody know why this happens? or experienced this before?

any advice on what i should do?

thanks a lot.

Is it still losing coolant? Sounds like maybe the heater box is leaking coolant into the ducting.

Can u smell coolant with the heater or aircon on?

hey i haven't really tested it. what is it meant to smell like? i'll try it and get back to you.

i called nissan service center and they said they won't look at it cos its an import, something about how they're computers won't sync with mine :(

i called my dealer skyimports in melbourne and they said they'll have a look on tuesday.

is it still ok to drive it around? how severe is the problem? i clearly dunno much about this.

thanks a lot btw.

hey i haven't really tested it. what is it meant to smell like? i'll try it and get back to you.

i called nissan service center and they said they won't look at it cos its an import, something about how they're computers won't sync with mine :(

i called my dealer skyimports in melbourne and they said they'll have a look on tuesday.

is it still ok to drive it around? how severe is the problem? i clearly dunno much about this.

thanks a lot btw.

the air con doesn't smell or anything but i had a look at the coolent and its almost empty...

... what is it meant to smell like?

^ ^ ^ a bit like 34 minute-old ejaculant on floor of passenger footwell :P

see if coolant is leaking behind glove box where heater core might be

shut off heater

refill coolant before driving and take spare water with you whilst driving until it's attended to on tuesday

if you arent leaking water, it means you havent bled your coolant system properly. the sound you're hearing is the water moving around in the air gaps inside the heater core. bleed your coolant properly and it should go away.

if you arent leaking water, it means you havent bled your coolant system properly. the sound you're hearing is the water moving around in the air gaps inside the heater core. bleed your coolant properly and it should go away.

hey thanks, yup there's nothing leaking atm.

i'm new to all this. is bleeding the coolant easy to do? what does it involve doing?

thanks a lot.

you need to get all of the air out of your coolant system. it involves filling up your radiator, letting the car get to operating temperature and revving the engine to about 3000rpm every now and then while still keeping the coolant topped up. you need to keep an eye on the temperature, making sure it doesnt overheat.

you need to be doing all of this while the heater is on full heat @ full fan speed. when it seems like its not releasing any more air, close the radiator cap, let it idle for a little while then crack the bleeder nut which is at the highest point of the cooling system.

if its your first attempt i suggest searching 'how to bleed cooling system'. or get it to a mechanic to sort out.

this has the potential of doing a bit of damage if temps get too high so be careful and dont be afraid to turn the car off if you feel like the temperature is getting too hot.

you need to get all of the air out of your coolant system. it involves filling up your radiator, letting the car get to operating temperature and revving the engine to about 3000rpm every now and then while still keeping the coolant topped up. you need to keep an eye on the temperature, making sure it doesnt overheat.

you need to be doing all of this while the heater is on full heat @ full fan speed. when it seems like its not releasing any more air, close the radiator cap, let it idle for a little while then crack the bleeder nut which is at the highest point of the cooling system.

if its your first attempt i suggest searching 'how to bleed cooling system'. or get it to a mechanic to sort out.

this has the potential of doing a bit of damage if temps get too high so be careful and dont be afraid to turn the car off if you feel like the temperature is getting too hot.

hey thanks for all that info.

i did go see a mechanic today. we tried running the heater on to verify the sloshing sound but nothing happened. because its intermittent and the mechanic couldn't hear it, he asked me to come

back if the coolant runs low (?). i mentioned bleeding the coolant but he said that he can't confirm anything at this point.

would you recommend getting a another mechanic to check it out?

thanks!

Edited by greenpool

Need to get the air bubbles out of the coolant mate.....happened to me with my old 180sx when I installed a new PWR radiator.

I bleed the system but it still had bubbles in the coolant, just keep bleeding it over the next couple of drives and should go away.

Also I squeezed the radiator hoses to push the air bubbles out which helps.....and you need to get the water hot enough to open the thermostat.

I normally cut a 2lite bottle in half and tape it to the top of the radiator so the water level is higher than the engine which helps push the water down.

Edited by 180JDM

get any brand but make sure its concentrated or get a 50/50 blend. some do a 30/70 on non turbo cars (30 coolant/70 water). its up to you which one you go for - its just an anti-boil/freeze additive.

you'll find that the concentrates are a little cheaper than the pre-mixed stuff.

another quick question.

i've currently got the coolant tank filled with water. above the max cos i didn't know any better lol.

when i've got the coolant, can i mix it with the water? OR wait till the water evaporates and then fill it with coolant?

thanks a lot for ya replies.

you dont need to put anything in the reservoir tank. if its over-filled then it will just drain if your fuel cap ever releases any pressure. its not something you need to fill up.

just concentrate on putting coolant into your radiator.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...