Jump to content
SAU Community

Recommended Posts

Just getting into Rotax racing, wondering if any of you guys are already out there with www.canberrakarts.com.au

Its great for competitive people as its a sport where you can actually race other people rather than doing trackdays where you don't race anyone other than yourself.

I found after doing track days, the costs were adding up to.

A new set of slicks for the kart is $250 compared to $500 a tyre for RE55s.

Brake pads are less than $50 compared to $600 for a set for the car and everything tends to last longer too.

And the main thing in karting is everyone all has the same gear, so its a real chance to test your driving skills against others.

Hope to see some of you out there!

Link to comment
https://www.sau.com.au/forums/topic/356959-anyone-here-kart/
Share on other sites

I'd considered it, but it's a bit too much of a dedication for me. There as a dude here trying to get rid of all his karting gear for around the $6k mark I believe (inc trailer) which looked pretty amazing since it should get you straight into your first race...but the time would just be too much on the side :(

I found after doing track days, the costs were adding up to.

A new set of slicks for the kart is $250 compared to $500 a tyre for RE55s.

Brake pads are less than $50 compared to $600 for a set for the car and everything tends to last longer too.

Get the Federal tyres for a good cheap alternative to RE55's, and my full race brake pads I imported from America at half the cost locally. You can make a lot of savings if you try.

Saying that any smaller vehicle is far cheaper to run and less damaging to components. I run a stock motorbike that apart from fuel has never cost me anything to repair or replace doing multiple track days.

Only advange to the car and bike over a cart is I can drive them to the race track and drive them back, and they have a much broader market when I want to sell them.

Only thing with running the federal RSR's is that you are instantly 2 secs a lap slower over RE55's even more so if you run AO50's or DZ03's.

A mate of mine was QLD u16's cart champ a few years back....carting is all about budget/the best equipment, he went from mid pack with a cheaper cart, then bought the best cart avaliable and blitzed the field everyrace without trying.

So its cheaper if you wanna go have fun, but if you want to win it gets just as expensive as running a car at supersprint days.

Which is why I never bought a cart when I had the chance.

Not saying dont do it, because its awesome fun.

Only thing with running the federal RSR's is that you are instantly 2 secs a lap slower over RE55's even more so if you run AO50's or DZ03's.

Never.... :) That would put me in the same time bracket as Dennis in Duncan's full race car. With Dunacan only a second and a half faster again. http://www.natsoft.com.au/cgi-bin/results.cgi?05/03/2011.WAKE.S6.Y

With Slicks I could probably pick up 2 seconds, but you seem to be saying upgrading the RSR's to real semi slicks will gain about 3 seconds. That's like saying my mostly stock GTR is as fast as the best SAUNSW car around Wakefield.

I'd love to say you are correct, but I'm not that good.

It's a fantastic sport and you'll have a blast mate.

Karting forums often mention that if you're going a bit slow it's a problem with the spacer. Spacer refers to the item between the steering wheel and the seat, ie: the driver. It is true that if you buy a brand new chassis and engine you'll have an advantage, but it is mostly driver skill. I'm sure lewis hamilton could get in a kart 10 years older than the field and blitz them, at sub world class anyways. Setup also makes a big difference, by changing to the correct jet you can save a full second a lap.

But instead of spending the best part of 10k on new parts, you can buy a kart plus engine for 2500 and go. Mine is for sale for 5k ono now, and i really regret leaving the sport. Unfortunately I can't afford it atm, I couldn't afford to keep the r34 either.

One more point, if you exchange some paint on a track day it's a big pain. If you do it in a kart it's just normal racing. There are no fancy paint jobs to scratch or delicate panels to bend. I've seen some fairly high speed crashes (maybe 80km/h backwards into the tyre wall) where the person dragged his kart back onto the track and started up again, kart un-damaged.

I look forward to the day I get back into it, but at the moment I'm just trying to get enough money together to last this year at uni, so I can get out and earn some money!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...