Jump to content
SAU Community

Recommended Posts

hey guys i recently aquired a pair of turbos that the last owner thought were STANDARD r32 gtr turbos... THEY ARE MOST CERTAINLY not standard...

specs from what i can see and read are as follows,

comp housing is A/R .60

turbine housing is A/R .64 and the housing does not have a divider in the rear between the turbine outlet and the wastegate outlet

the actuator rod is also adjustable...

the part numbers are very strange and make no sence to me at all??? so let me know what your thoughts are.

part number is as follows....

14411 RS580

WL 9012J

486089-0005

ANY HELP WOULD BE MUCH APPRECIATED,

cheers

Link to comment
https://www.sau.com.au/forums/topic/357135-what-are-these-turbos/
Share on other sites

Get your google on:

http://www.gtr.co.uk/forum/7428-garret-r-60-m24.html

I always thought they were what was used in the Gibson pack of arseholes car but I could be wrong...

Either way they are going to make bulk power and be laggier than -9s but possibly similar to -5s without the 400+kw capability. If they are on the car already just run with it, if not try sell them on and get a set of the newer gen options to suit your goals.

2860-9 for 300ish wkw

2860-5 for 400ish wkw on a built motor

i have ust noticed that all of the charts and specs say that the 14411-rs580 is a turbo called (nismo for street) and it is supposed to have a .42 A/R...

now i am more confused as these have a .60 AR compressor housing? :blink:

thanks for the info so far guys..

these are for my spare motor so they will do for now,

not too bad for $50 tho :thumbsup:

hmmm i wonder what they are worth to sell? lol

Ye but not bad in terms of what?

they will make power, but will do so with ridiculous lag. Bad choice really.

Better off selling them for $1000 (seems about the going price) and buy some decent turbos with 1200-1400 more ontop and never worry about it again

Yup, nismoid that's what the plans are.. I have already used all different types of new style ball bearing Garrett turbos -5s, -7s and -10s and then went to a t51r.. These were only bought because I could tell from the pictures that they aren't standard and they were cheap.... As I said for my spare motor for now they will do until I get my custom made 3076's with -10 housings in a few weeks... Even -10s are too small for 3.2 litre 26/30

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...