Jump to content
SAU Community

Recommended Posts

Looking to replace my cat on my 34 GTR, do I require one with a provision for a sensor in it or doesnt it matter

same situation, so subscribed

my current tiny compliance cat has no sensor in it, but i have seen Cat for GTR on Just Jap has provision for a sensor

Car runs HKS F-COn with no Air flow meters, not sure if this has anything to do though

Link to comment
https://www.sau.com.au/forums/topic/357833-r34-gtr-cat/#findComment-5718968
Share on other sites

its just a sensor that has no effect on ECU.

basically just a dash light/warning.

and once you mod cars, there is more heat etc effectively making it pointless anyway.

if you want exhaust temp, a proper sensor in the dump pipes is what's needed.

Link to comment
https://www.sau.com.au/forums/topic/357833-r34-gtr-cat/#findComment-5718990
Share on other sites

its just a sensor that has no effect on ECU.

basically just a dash light/warning.

and once you mod cars, there is more heat etc effectively making it pointless anyway.

if you want exhaust temp, a proper sensor in the dump pipes is what's needed.

Thanks

I do have ex.temp showing in the display, but not sure where it getting picked up from

Link to comment
https://www.sau.com.au/forums/topic/357833-r34-gtr-cat/#findComment-5719489
Share on other sites

yes, 34 GTR have ext temp sensor in the dump pipe and also have the cat overtemp warning sensor in the cat. the cat sensor is not that important, but if you are buying a new cat may as well get one that has provision for the sensor as it's nice to know if your cat is overheated/blocked/damaged.

Link to comment
https://www.sau.com.au/forums/topic/357833-r34-gtr-cat/#findComment-5719728
Share on other sites

its just a sensor that has no effect on ECU.

basically just a dash light/warning.

and once you mod cars, there is more heat etc effectively making it pointless anyway.

if you want exhaust temp, a proper sensor in the dump pipes is what's needed.

ok so the temp sensor for the mfd is near the O2 sensor? good to know.

yeah the sensor in the cat is just for the warning light on the dash, so if that light comes on genarally your cat is gone or going, was unsure if it did the ex temp for mfd aswell

Link to comment
https://www.sau.com.au/forums/topic/357833-r34-gtr-cat/#findComment-5722058
Share on other sites

if you re-read my post u will see it says " v-spec r34's"... as only cars with the mfd #2 have the exhaust temp and another inlet air temp sensor in the cooler plumbing....

ie. normal non-vspec r34's will not have these

Edited by BrynDETT
Link to comment
https://www.sau.com.au/forums/topic/357833-r34-gtr-cat/#findComment-5723004
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...