Jump to content
SAU Community

Recommended Posts

I havn't heard back for half a week now - emailed three times. Not sure what the go is.

We are all getting the oil coolers with the coloured fittings and then the black fittings are getting sent out seperately.

  • Replies 334
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Righteo I got a reply. They have been flat out and he didn't have time to reply.

All the oil coolers are ready to go, fedex should be picking them up today or tomorrow.

We get to keep the red/blue fittings and hopefully the black fittings shouldn't be to much longer. The fittings are worth 50GBP in total so if you sell them atleast you get a little bit of cash back for the delay.

  • 2 weeks later...

I've emailed them three or four times in the last week and still no reply. It's still early Monday there now so might get a reply tonight after the weekend.

Really hope so as I'm not happy with the cut off in communication!

UPDATE

YAY! Good news guys. Got half of the tracking numbers just then and will receive the other half tomorrow. I'll PM everyone their numbers and chuck up the list.

People i'm still awaiting tracking numbers for are:

J34

A20089

CASSBO

WLSPN

EIGHTSIXBOY

So hopefully tonight.

The rest of the guys should have got a PM from me with their tracking numbers.

Nah no idea man. Also I need to message him about your kit as to what the go is with it.

I just checked the old tracking number you originally gave me and its still only says 'initiated' so it was never sent by the looks of it.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...