Jump to content
SAU Community

Recommended Posts

Selling some unwanted parts, located in Melbourne Pics coming soon

a) R33 Cusco Front Strut bar - $100

some scrapes but in good Condition,

b) R34 GT-T Blitz Induction cover and Sus power LM panel filter - $150

Rare, no longer produced for Skylines. T-304 Stainless steel induction cover replaces stock air box cover for optimal air flow.

Comes with used Sus power LM filter.

c) Blitz Power Meter ID III - $180

Brand new, never installed, complete with manual. No box

d) R33 Blitz SUS POWER Stainless Steel Pod Filter - $100

Pod filter made from T-304 Stainless steel. Comes with adaptor plate whcih should fit the standard AFM. No replacement needed, just clean with compressed air hose.. Makes a great induction noise.

Link to comment
https://www.sau.com.au/forums/topic/358093-blitz-cusco-parts-for-sale/
Share on other sites

Selling some unwanted parts, located in Melbourne Pics coming soon

a) R33 Cusco Front Strut bar - $100

some scrapes but in good Condition,

r33strutbrace.jpg

b) R34 GT-T Blitz Induction cover and Sus power LM panel filter - $150

Rare, no longer produced for Skylines. T-304 Stainless steel induction cover replaces stock air box cover for optimal air flow.

Comes with used Sus power LM filter.

inductioncover.jpg

c) Blitz Power Meter ID III - $180

Brand new, never installed, complete with manual. No box

powerid3.jpg

d) R33 Blitz SUS POWER Stainless Steel Pod Filter - $100

Pod filter made from T-304 Stainless steel. Comes with adaptor plate whcih should fit the standard AFM. No replacement needed, just clean with compressed air hose.. Makes a great induction noise.

suspro.jpg

  • 4 weeks later...

Bump

also selling

Whiteline -KCA347 adjustable Camber bushes. (brand new , unused) - $110

Essential for those lowering their cars.

Description: Toe correction - control arm lower inner & outer

Note: KCA347 is designed to replace the rear upper control arm-out

http://www.whiteline.com.au/product_detail.php?part_number=KCA347

  • 1 month later...
  • 8 months later...
  • 11 months later...
  • 1 month later...
  • 4 months later...
  • 3 months later...

Induction cover sold. Remaining items still available. I also have 2x nismo original polos bought from omori factory for sale at $50 each. Make an offer. Need them gone. Pm or SMS at 0432182133

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...