Jump to content
SAU Community

Recommended Posts

Hi all, not sure if there is a problem and I am going to get a mechanic to have a look when it gets a service done, but I just wanted to have some idea what might be wrong when I talk to him about it.

Its a GTR and the clunking can be heard when I feather the accellerator on and off, just enough to get the car lurching foward and the clunking sound seems to come from somewhere around the front of the gearbox and only makes the noise when in traffic etc and not when the car is accerating smoothly through the gears.

I have checked the engine mounts and gone over everything that I thought might be causing it by jacking the front end up and shaking any moving parts but everything seemed ok.

It have a heavy duty double plated clutch that rattles and caries on like they do but I don't think thats the problem.

If I had to have a guess I would say where the engine joins the gearbox there seems to be something loose or worn there and there is excesive play .

Any thoughts would be appreciated especially if it could be the heavy duty clutch and I might not have a problem at all.

Thanks Ian

Link to comment
https://www.sau.com.au/forums/topic/360661-clunking-sound-at-front-end/
Share on other sites

Diff/Drive Shaft bearings.

Had the same issue as do many of us with this age car.

Thanks for that, I will have a seach for how to fix it, but if its ok to ask is it a big job and something that could be done at home.

thanks Ian

putting in search for driveshaft bearings has given me a heap more reading to do so thanks, gearbox mount is something that has come up so will need to have a look at that, of to work now but will investigate more tomorrow.

Hardest part will be to find a second hand diff in good condition, which will save you a few dollars else you'll need to spend money reconditioning your existing one.

For me, a few quotes were ok to outrageous depending, but at the end I was lucky and got a good condition diff for $450 and the driveshaft issue done for $400... then you slap labour ontop plus some new bushes/mounts and you'll get your total.

Worth the fix though and I'd suggest you shop around to make sure you're getting the most, don't feel shy to ask as many questions as you can.

Good luck mate.

Can rule out the transmission bracket and cv joints. The noise is almost certainly forward of the gear lever and it might be just to the passenger side of centre. I will read up on how the front driveshaft works as I don't think it is the rear driveshaft/diff from where the noise is. Thanks to the poster that explained how to check the cv joints in another thread.

Think I can rule out the driveshaft splines as per the test of foot on brake and quickly let the clutch partially out in both forward and reverse. No noticable sounds.

thanks to the volvo forum for the test as per pasted below

"its either the driveshaft splines or the dual mass flywheel, its not unusual for the flywheel to make that kind of noise as it does move back and forth about 25 mm or so witha change in load .

To check the drive shafts press the footbeake on and select 1st then Reverse and let the clutch up partialy fairly firmly to put a sharp load through the transmission ( without moving of course as you have the brakes on . do reverse then 1st to reverse the load , if it clicks the first time you say go forward but not the second time without going into R , then its just the driveshaft splines .

If the noise is light when going on and off the throttle at low speed then it's probably the dual mass flywheel ...

Neither is a bad problem ..."

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 😅
    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...