Jump to content
SAU Community

Recommended Posts

  • Replies 163
  • Created
  • Last Reply

Top Posters In This Topic

Uhm... I wouldn't go to that meeting spot if I were you. There's been trouble there in the past with hoons and it's a pretty well known meeting spot.

Maybe choose somewhere different?

So we still rock solid on the meeting spot and/or route Glenn?

Might be an idea to change it if Erin is right then there is prolly gonna be lots a cops if it is a known area for hoon collecting........??

I know a spot right around the corner from where I live like that,lots of hoon gather and flex their tyres, little industrial estate, but cops regularly cruise through, you can tell because suddenly 20 cars will whizz past my house all coming sideways out of the round-a-bout, bunch a idjuts!!

i don't think that the 2 PMs that i sent out are confusing.

The 1st PM informs everyone on the list where we are going and the route which we will be taking.

The 2nd PM is for the meeting point for both Brisbane and GC crew to unite. Since the proposed carpark is a bad meeting spot cos its hoon-populated, the NEW meeting spot will be @ Wishart Village. (UBD Page 201 Ref: J5) at 8.30pm

i am glad that i'm able to get both Slip and Gary1 to come on this cruise.

so once again:

Brisbane Crew - Meet at Milton Maccas @ 7.45pm.

GC Crew - check with Ska but i am sure that you guys have been well informed by him.

Both sides will unite at Wishart Village @ 8.30pm.

glenn

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...