Jump to content
SAU Community

Recommended Posts

got any tricks for clamping a donut in the small vice on those types of saws?

think i worked out a way with the angles

clamped the 180 down to a bench and marked the exact centre, then used a protractor from that point squared up to the bench.

i THINK that should mean that the tube will remain 3inch on the cut

I use a small vertical bandsaw, I can usually get the cut very close by hand/eye, then linisher to clean it up.

Its the main reason I prefer lobster bends as I find it much easier to cut the angle required in the brobo, I can also change the radius of the bend along with creating smooth spirals etc. Its a bit more welding but I need all the practice I can get with alloy. :)

yep, lobster is looking easier for this pipe

just cant decide, dont want to mix the 2 piping styles too much so was looking for ways to do it better.

would be alot easier with a vertical bandsaw, but the small ones i have used were crap as a vertical saw

I have machined up a set of mandrels and guides.

I'll use a 4in donut as an example.

A tight radius 4in might have an ID of 2.5inches.

So I've machined up an alloy mandrel from round bar which is 2.5 in diameter.

It also has been in the mill and a slot about 1/2pm wide cut along it's length.

It's about 3in long and has a 1in pair of flats milled on one end.

I removed the table from my vertical bandsaw and used the mill to cut a 1in groove in the dead center of the table inline with the blade.

The machined mandrel sits in the groove located by it's flats dead center to the blade.

The welded dounut slides over the mandrel and hence is located dead center to the blade as well.

The mandrel can slide in towered the blade and the donut is cut perfectly straight and always remains perfectly square. When you come to the end of the cut the bandsaw blade enters the slot I milled into the mandrel an doesn't damage the mandrel at all.

Rotate the dounut around to cut the section out your want and feed it back into the blade. Perfectly square and straight again.

I have several mandrels which all have the same set of 1in flats and all fit into the same groove on my bandsaw.

If I need to do an odd size I just machine a new one to suit the ID of whatever dounut I'm using.

Does that make sence?

Whe youbuy small bandsaw bring the table down and I an mill the groove in it.

If you buy some alloy bar and tack weld some of the common dounut sizes you want to use we can machine up some mandrels at the same time.

Doesn't take long on the machines I've got and saves you alot of time in the long rub

Whe youbuy small bandsaw bring the table down and I an mill the groove in it.

If you buy some alloy bar and tack weld some of the common dounut sizes you want to use we can machine up some mandrels at the same time.

Doesn't take long on the machines I've got and saves you alot of time in the long rub

sweet offer, thanks brad!

got any pointers for the vertical bandsaws? for alloy i would think that with regular cleaning a woodworking bandsaw would suffice, but im open to good suggestions or examples of the type of vertical saw i should be looking for.

was thinking somethign like this

https://www.machineryhouse.com.au/Products?stockCode=W4224#

I think most people use 7 deg cuts for all but the end pieces.

not 100% on that as my best effort at fabrication is a flat piece of alloy with holes in it lol

hahahahahaha

yeah i use 7 degree cuts, varying the lengths to change the radius

Hafco gear is pretty good. I have a few things from there.

I'd also have a look on Greys online.

I started with a small ryobi saw from bunnings. Still use it too.

All you need is something with a decent bed so it can have a slot milled into it

  • 1 month later...

im just using the wood blade for alloy, same as on drop saws - take it slow and there really isnt too much issues.

i picked up the H&F one i linked above already and it is handy as for small alloy jobs, heaps better than an alloy grinding blade

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...