Jump to content
SAU Community

Recommended Posts

Hi Guys,

We are looking at running Michelin 27/68-18 (682mm high) slicks on all four corners. We can get these cheap second hand ex-Porsche cup (about $250/set).

Will these be too tall? I gather the V-Spec's ran 225/50-17's which are about a 657mm rolling diameter, so we would only be about 25mm oversize.

I assume the width is not such an issue, we are looking at getting a set of Enkei RPF1's in 18x10.5 ET18.

We are currently running 24/625-17's which are obviously not a problem. We could also get 24/65-18's (also ex Porsche cup) and get some 9.5" wheels but would rather run the wider setup.

Cheers for your help!

Link to comment
https://www.sau.com.au/forums/topic/361948-running-2768-18-slicks/
Share on other sites

Make sure that they are not a specific construction to cope with the "unique" layout of the Porsche Cup Cars, I am aware that the euro series do have their own spec Michelins, I'm not sure if it is the same here.

Make sure that they are not a specific construction to cope with the "unique" layout of the Porsche Cup Cars, I am aware that the euro series do have their own spec Michelins, I'm not sure if it is the same here.

Good point, it was suggested we don't run the fronts (the 24/65-18's) as this is the light end on the Porsches.

Hi Guys,

We are looking at running Michelin 27/68-18 (682mm high) slicks on all four corners. We can get these cheap second hand ex-Porsche cup (about $250/set).

Will these be too tall? I gather the V-Spec's ran 225/50-17's which are about a 657mm rolling diameter, so we would only be about 25mm oversize.

I assume the width is not such an issue, we are looking at getting a set of Enkei RPF1's in 18x10.5 ET18.

We are currently running 24/625-17's which are obviously not a problem. We could also get 24/65-18's (also ex Porsche cup) and get some 9.5" wheels but would rather run the wider setup.

Cheers for your help!

R35 Duncan ran the Michelin's, new and used - had some concerns on heat cycles etc with some.

I ran Dunlop 280x 680 x 18s on R33 you will have issues with inner guard plastics front and rear, fuel filler plastics foul, if you are lucky enough to get some grippy ones even not running spacers stock up on wheel bearings.

The 25mm oversize will give you about 1/2 a gear difference - so depending on horse power, torque and the track you are running - something to keep in mind

Cheers

get the 27-65-18. front tyre for gt3-rsr. also used on a few production sport cars too.

ive got a couple stacking up in my garage. (used to work for the utes and lots left after each meeting...)

they do fit under my missus r33 gtst. so 32 gtr wouldnt be an issue. but a wheel with +22 or greater will help fitment. (guard clearance) z32 wheels with a custom bolton spacer thickness would be the easiest option

  • 2 weeks later...

They will fit. However you will have to remove the inner wheel arch guards and the factory blow off valves if you still have them. The car will ride hi but it's not too much of an issue if you set the car up right.

Last time I saw the Windfield GTR at eastern creek it was running these exact tyres.

They will fit. However you will have to remove the inner wheel arch guards and the factory blow off valves if you still have them. The car will ride hi but it's not too much of an issue if you set the car up right.

Last time I saw the Windfield GTR at eastern creek it was running these exact tyres.

Thanks Jay, (I co-own the car with savant/ Willie)

If that's all it will take then it's worth it for the price saving on buying slicks alone.

So you reckon, just removing the plastic wheel arch liners is enough, no guard rolling needed?

Does anyone know what dimension the tyres were on the Bathrust GTRs?

Cheers mate,

Ollie.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...