Jump to content
SAU Community

Recommended Posts

So i got defected for this item last night, owned the car for 4.5 years and never had a problem. It's a dual port turbosmart BOV, So the trumpet is on one side and the other is plumb back...i read up on this and apparently they come with a blanking plate. The BOV was on the car when i bought it so i didn't receive this item (Blanking Plate).

I was under the impression that it could just be changed back without having to take the trumpet off, cuz the cop last night had to watch it go off. But if it is suppose to be removed and a plate put over the top, wouldn't you just defect all bov's with a trumpet?

Anyways i don't mind having to stop it...Is there anything particular i need to watch for if i cap this off, or would it actually be considered better, performance wise?

Where is the best place to find these covers?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/
Share on other sites

So is it currently using the recirc or not?

If you block off the ATMO side, you'll need to ensure the recirc side is all connected. Then no problem.

You could probably order the plate off a turbosmart distributor/stockist. If not just have one made/cut up. Wouldn't be expensive.

Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/#findComment-5777899
Share on other sites

Go here, http://www.turbosmar...index.php?id=47

The part you will need is a 'BOV Port Blanking Plug'

Model number: TS-0205-3103

It's better plumbed back if you run a stock ECU. Buy the plug, unscrew the trumpet, screw the plug on. Done.

Autobarn have these plugs.

Edited by Aleckr33
Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/#findComment-5779999
Share on other sites

cheers...just did a google image search...

are these plugs round? i was thinking that'd just be like a rectangle plate that replace the trumpet plate.

Or is it round and goes in the hole and put the trumpet back on top of it?

Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/#findComment-5780022
Share on other sites

mine looks a little different, the trumpet is on a rectangle plate. Same with the plumb back side, its got 4 allen keys holding each in place.

http://i11.photobucket.com/albums/a153/spiralsmurf/DSC01184.jpg

Edited by 3340TH
Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/#findComment-5780239
Share on other sites

y's that? the part on the right goes back into the intake. 50% goes that way 50% goes out the trumpet. Would it damage something to put 100% back through the intake side?

Edited by 3340TH
Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/#findComment-5780274
Share on other sites

I bought the car in 06 and was on it then..i just pulled it out then, trying to find an allen key that will fit it right...but it looks as though i can remove the whole plate, but also the trumpet goes inside the plate...so whether i can unscrew it from that plate is another story but i cant budge it atm.

EDIT: It unscrews.

Also whats the business with the hard soft with the tension of the spring. better hard or soft?

Edited by 3340TH
Link to comment
https://www.sau.com.au/forums/topic/362032-turbosmart-bov/#findComment-5780357
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...