Jump to content
SAU Community

Recommended Posts

Hey guys, I am having some problems with my gtr motor and would love some help. To begin with the engine was yanked, pistons changed, rod bolts changed to arp, headgasket was the cometic superstreet hg. My engine management is power fc (got a used one from my engine builder). Head was ported and polished, tomei procams installed with tomei solid lifters, valve springs and retainers etc.. I have been having very low compression since the build, pretty much 90-95 psi across the board. Now here lies some of the other problems, the car has been mildly tuned and when I get on the car the idle becomes really rough and it takes a little while for it to clear up. I started to get compression readings of 0, 30, 90 and now 50 psi on number 4 cylinder. The other cylinders hold at 90 psi. I get no smoke so it leads me to think that the problem is in the head. I am going to be taking the motor out in a couple days to see what's going on but my new problem is now this, yesterday while driving the car it started to give me the "subaru sound" when I stopped I noticed that number 5 was not firing, I have injector pulse and the plug is wet. I also noticed the coilpack had a huge crack on it. I tried to tape it up and the replaced it with the coilpack from number 4. I also changed the plug. I cruised home and when I got home, decided to check the coilpack again, where I saw that the replaced coilpack also cracked! So now I have TWO cracked coilpacks. I have use the gtr manual to check the wiring and also the ignition relay, I ran out of time but I will be checking the power transistor when I get home. Do you think that the power fc is the problem and has anyone else had this problem? The engine is from a 96 gtr and is in a 97 240sx. Going to post a picture.

post-26402-0-77406500-1304200065_thumb.jpg

Edited by steeldawg_69
Link to comment
https://www.sau.com.au/forums/topic/362659-cracked-coilpacks/
Share on other sites

Check that the coilpack cradle is sitting correctly. Also what spark plug are u using? Maybe the spark plug is too long or not completely down in the spark plug well/thread. Check this very carefully.

Does the spark plug screw all the way down?

Check the thread

As for the compression pour some oil down the bad cylinder and see if the compression test result is higher.

If not then maybe the valves arent lapped in correcty or maybe the valve is beeing held open by incorrectly fitted shims

Ok will definately do that. I checked to see if there was anything hindering the plug from going in. It went in without hassle. I just cant figure out what would make two coilpacks pop like that within 15 mins of each other. I'm going to recheck all my grounds. I almost forgot, the builder could not find my shims and he had the machine shop make some, now I'm starting to think......oh boy!

Edited by steeldawg_69

'Low' compression isn't a problem so much as constant compression, as mentioned in other threads and in here due to dodgy testers or badly done.

The problem is, as you have, when one or more are vastly different than the rest.

Good luck with the fix.

Did you speak to engine builder about the compression? Is it actually a problem?

You need to address the coilpack issue completely first, and only once that's done work out if you have a real problem. If it were me, i'd put it back on the dyno once the coilpack issue is fixed and see if it makes the right power. If not, ask the engine builder why you're getting those compression test results.

Big cams can effect compression results, so maybe get a leak down to back it up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...