Jump to content
SAU Community

Recommended Posts

Observe the below, detailed and to scale diagram of my intended oil cooler setup. I currently have an oil cooler setup so I don't want to hear anyone saying sell it and buy one with the thermostat.

Anyway this is my idea as below.

1 sandwich plate with built in thermostat for the oil cooler(Mocal branded)

1 sandwich plate for oil relocator

all the hosing and the bla bla parts.

Is this a good idea using a sandwich plate on a sandwich plate?

Ive also attached a second picture which shows the use of an inline oil thermostat which opens at 82C.

The first option is messy but saves about $100. This setup will cost me about $80

The second option is nice, neat and cost about $190.

I payed $200 for the oil cooler plus relocator kit so keeping it as cheap as possible would be great. Its a just jap oil cooler 10an fittings.

Input would be greatly appreciated.

post-68383-0-95405800-1304838903_thumb.png

post-68383-0-62624600-1304838909_thumb.png

Link to comment
https://www.sau.com.au/forums/topic/363513-oil-cooler-setup-with-thermostat/
Share on other sites

I have seen Greddy thermostat sandwich plates going for $170 on ebay, I bought the mocal one first and it was just a spring blocking a hole with nowhere to put my senders, the Greddy was a proper plunger style thermostat.

Do you still have the mocal? Id consider the greddy thermostat but for the same price I can get the inline setup. If I get the greddy one I'd have to run a sandwich plate on a sandwich plate to use my oil relocator and I need to know if this is a bad thing to do...

Observe the below, detailed and to scale diagram of my intended oil cooler setup. I currently have an oil cooler setup so I don't want to hear anyone saying sell it and buy one with the thermostat.

Anyway this is my idea as below.

1 sandwich plate with built in thermostat for the oil cooler(Mocal branded)

1 sandwich plate for oil relocator

all the hosing and the bla bla parts.

Is this a good idea using a sandwich plate on a sandwich plate?

Ive also attached a second picture which shows the use of an inline oil thermostat which opens at 82C.

The first option is messy but saves about $100. This setup will cost me about $80

The second option is nice, neat and cost about $190.

I payed $200 for the oil cooler plus relocator kit so keeping it as cheap as possible would be great. Its a just jap oil cooler 10an fittings.

Input would be greatly appreciated.

the second pic is the way to go so the oil goes through the filter no matter what, I have the Mocal themostat ( not installed yet ) it should work fine, while cold and thick the oil takes the path of least resistence and returns straight from the filter ( in diagram 2 ) when the oil gets to a certain temp that path is slightly blocked and the oil goes through the cooler then back to the motor..

the second pic is the way to go so the oil goes through the filter no matter what, I have the Mocal themostat ( not installed yet ) it should work fine, while cold and thick the oil takes the path of least resistence and returns straight from the filter ( in diagram 2 ) when the oil gets to a certain temp that path is slightly blocked and the oil goes through the cooler then back to the motor..

Are you going to with the same in line setup? A sandwich plate on a sandwich plate will still let the oil filter filter the oil but it requires double the length of hose. scotty is going to show me pix of a thermostat he might have. Options are still open so.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...