Jump to content
SAU Community

Recommended Posts

All sorts of crap for sale and plenty more not listed, if you see something in the background you want come get its all got to go. Located in Glenfield in sydney.

Call/sms 0400 604 293 or reply on here.

TURBOS

R32 gtr turbos, blown $20

R32 gtr turbos with actuators, working fine when removed, never boosted hard they were for running in only $100

post-26632-0-39364200-1304847521_thumb.jpg

R33 GTr turbos, removed from motor I got for the race car complete with dumps etc. I will keep the 02 sensors though $200

post-26632-0-33406000-1304847908_thumb.jpg

Custom GTR dumps and front pipes, nice merge from the wastegates. $200 from turbos to cat

post-26632-0-44728700-1304847557_thumb.jpg

RB26 exhaust manifolds/ heat shields $20 each

Custom gtr turbo inlets, front and rear. Provision for blowby but removes plumback for BOV's $30

post-26632-0-41725800-1304847584_thumb.jpg

ENGINE BAY

R33 plastic undertray $10

post-26632-0-07253600-1304848130_thumb.jpg

R32 GTR radiator overflow tank $10

R32 GTR washer bottle $10

RB25 coilpack cover $10

RB25 Inlet manifold with bolts and gasket. $20

RB26 Front Timing cover Black and Clear $20/$40

R33 GTST a/c auxillary fan $10

R33 GTST GREDDY fmic piping kit, cold side $50

R33 GTST piping from Throttle body to drivers guard, without going over to the exhaust side rocker cover, kept room for big turbos $20

R32/R33 GTST piping with 2x bov from throttle body to standard intercooler holes on passenger side, again keeps room for big turbos $20

GTR turbo setup piping instead of "twin turbo" pipe, crosses behind radiator. Had used in conjunction with the above pipe with 2 bov's to use the gtr manifolds on the rb20 $50 (comes with BOV's)

MECHANICAL

post-26632-0-56316000-1304847951_thumb.jpg

R33 GTST intercooler and piping $50

post-26632-0-46216600-1304848489_thumb.jpg

R32 GTR brake booster $20

R32 GTR clutch booster $20

R32 GTR factory pedals $10 each

R33 GTST Brake lines front and rear $20

R33 GTST Front rotors still plenty of meat $50

post-26632-0-75189000-1304848001_thumb.jpg

R33 GTST throttle cable $20

R33 GTST Fuel pump with bracket, use to mount your bosch etc so you can do a quick swap $20

post-26632-0-83965000-1304848040_thumb.jpg

R32 GTR gearbox mount $10

R33 GTR water pump- replaced with N1, still in good condition $10

Power steering pump bracket $20

R32 GTR clutch fluid loop $10

BODY/STYLING

3d GT wing with brackets and stands, everything needed to fit, as new $100

post-26632-0-06195900-1304847463_thumb.jpg

R33 front reo, hacked up. Keep yours and use this one $30

post-26632-0-89148400-1304847627_thumb.jpg

R33 Boot in maroon / wine red $50

post-26632-0-78076700-1304847806_thumb.jpg

4L of Nissan ANO paint for series one R33 $20

R33 GTST factory wheels with tyres (4) $100

post-26632-0-29915500-1304848392_thumb.jpg

Wheels that came on my shell, fit GTR ok but don't clear my big brakes on the front anymore. Used to basically roll the shell around. (4) $200

post-26632-0-11391700-1304847757_thumb.jpg

SUSPENSION

S14 or R33 rear camber arms, brand new never fitted $100

post-26632-0-12530800-1304848089_thumb.jpg

R33 front castor rods, rubbers gone, put some new bushes and off you go. $10

post-26632-0-85835200-1304848270_thumb.jpg

R32 GTR steering rack, rubber great $40

post-26632-0-13660700-1304848308_thumb.jpg

R32 GTR Standard front upper arms $50

INTERIOR

R33 gtst parcel tray support $5

R33 Jack bracket in boot $5

R33 ecu bracket $5

post-26632-0-92926500-1304847713_thumb.jpg

Blitz boost gauge $5

post-26632-0-81797700-1304847855_thumb.jpg

Apexi SAFC $50

S14 ECU and AFM from the same car $80

SR20 engine Loom $100

post-26632-0-93885400-1304848227_thumb.jpg

RB26 loom suitable for making a haltech/motec loom etc, has connections but a clutch went and damaged it near the wiper motor. I had planned to use it to make a loom for the racecar. $100

post-26632-0-36629400-1304848192_thumb.jpg

The other loom pictured, I think is for sr20 aac etc don't remember. If it looks like what you need then grab it.

post-26632-0-55667100-1304848428_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/363534-amazing-amount-of-random-crap-sale/
Share on other sites

some details of the intercooler piping bits on offer

R33 GTST GREDDY fmic piping kit, cold side $50

R33 GTST piping from Throttle body to drivers guard, without going over to the exhaust side rocker cover, kept room for big turbos $20

First pic shows GREDDY piping and the black/silver pipe (was black now painted silver)

post-26632-0-79384800-1304929687_thumb.jpg

post-26632-0-95041400-1304929614_thumb.jpg

R32/R33 GTST piping with 2x bov from throttle body to standard intercooler holes on passenger side, again keeps room for big turbos $20

GTR turbo setup piping instead of "twin turbo" pipe, crosses behind radiator. Had used in conjunction with the above pipe with 2 bov's to use the gtr manifolds on the rb20 $50 (comes with BOV's)

post-26632-0-51932300-1304929710_thumb.jpg

The approximate layout, with bov's positioned to plumback in front of gtr turbos. I do not actually have pics of the grey pipes on a car as they were on Jago's rb20. priced basically because they have 2 BOV's.

post-26632-0-10571200-1304929658_thumb.jpg

post-26632-0-10600300-1304929629_thumb.jpg

also selling the adaptor plates to allow gtr manifolds to bolt onto rb20/25 exhaust side. where on my r33 for around 4 years $150

  • 2 weeks later...

SOLD:

GT Wing

All 4 R32 Turbos

R33 undertray

ADDED:

SAFC photos, found the Loom for it. Also have PDF instructions in english. Its the old one and was off an r33 gtst

post-26632-0-34886900-1306135361_thumb.jpg

i have no idea on postage to hobart, will see what i can get tomorrow.

carpark there has been interest in camber arms but they are still here.

coil pack cover is from r33. Only asking $10 buy it and paint it or modify or something

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean it's a bit late to say "This won't have any tangible effect and it is not worth spending more than about three seconds on it, please just enjoy the car" But I said it anyway. Does the pod actually get any airflow in that position behind a bumper like that?
    • Hey guys - apologies for digging this up. Has this website been shutdown or is the outage temporary?
    • So, went shopping at Just Jap for things that might work for the intake  After some trial fitting there I ended up with a 3" x 45° silicone bend, a 3" x 300mm alloy straight, and a humped joiner, some minor trimming will be required to shorten some of the stuff, but nothing that is beyond my "ham fisted" skills The guy at Just Jap was most helpful as we had all sorts of joiners,  bends and stuff out trial fitting  Laying it out above the stuff in there it seems everything will fit nicely, and looking at it, it is probably the way I should have been looking at doing it from the beginning, probably..... In the end it is a front bar off job anyway to remove the original stuff behind the front bar that is taking up the required realestate needed, so maybe a Thursday or Friday job And because I'm a hopeless consumer, I grabbed some new steel wheel nuts, the current ones are a spline drive type with a "security" socket, that somehow someone keeps misplacing, the new ones are a basic black steel 17mm hex socket In other news: I just did my "final" tax return, I am now officially a old retired veteran pensioner, and I'm milking the system for all it's worth,  life is good
    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
×
×
  • Create New...