Jump to content
SAU Community

Recommended Posts

Hey guys need som1 to repair my frontbar it's fiberglass sum dumb kunt did a hit n run in it in noble park Im located in noble park willing to pay with cash or grog I've got the bar off just need it fixed and resprayed white

Thanks guys pm me or SMS on 0466 910 750

Link to comment
https://www.sau.com.au/forums/topic/363654-need-a-backyard-job-done/
Share on other sites

http://www.skylinesaustralia.com/forums/topic/360319-beware-of-people-contacting-you-privately/

This is what can happen when you're a tightass and won't take your car to be repaired etc properly.

Beware my friend, it's not worth it.

http://www.skylinesa...-you-privately/

This is what can happen when you're a tightass and won't take your car to be repaired etc properly.

Beware my friend, it's not worth it.

lol that thread was worth it just for this:

lolwut.jpg

If you're on a budget, I've heard DT Panels are ok, I've never had any dealings with them though. A search here should uncover some good info : )

Check the latest page of the Victorian rides thread if you need an example of DT's work. Pretty much perfect.

Hey thanks guys much appreciated. I have 1 more question would someone be able to help me replace my fuel pump u just bought a walbro GSS-342 I'm just not that confident doin it myself cause don't wanna f*k it up I'll supplie a slab or a bottle jimme or jack. If someone can let me know thanks again 0466 910 750

If you're on a budget, I've heard DT Panels are ok, I've never had any dealings with them though. A search here should uncover some good info : )

They do decent work, not perfect, but if your on a budget they are great.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...