Jump to content
SAU Community

Recommended Posts

I have R32 front strut tops in the garage i think. 99% confident they are the same, I know the front shocks or coil overs are interchangeable between 32 and 33 for the only difference between the two cars is 33 rears are longer. Let me know if you want me to track them down?

I have R32 front strut tops in the garage i think. 99% confident they are the same, I know the front shocks or coil overs are interchangeable between 32 and 33 for the only difference between the two cars is 33 rears are longer. Let me know if you want me to track them down?

that would be good mate! how much would you be after?

I need money sale!

-chrome 17" work "vs" wheels

-Rb25 alternator, Igniter, coil pack harness, Air flow meter starting at $50

-rb20/25 cross over pipe from

Cefiro, factory BOV delete $50

-Rb26 r33 Front diff/sump, twin turbo pipe, ac, power steer pump

-s13 5 stud rear conversion with near new slotted s14 rotors $200

-front rotors r32 gtr, r32 Gtst, r33 Gtst, s14, slotted and not, various

-pair 4 stud alloy skidders 16 or 15x7 with tyres no pictures $50

-pile of 14" pintara/skyline steelies with tyres

-new coilovers instock s14, s13, r31 etc $750 pair or 1300 a set

-upgrade tie rods and ends s13/14/15 and r31 kits starting at 150 per kit

-skyline and silvia dual rear caliper brackets and full kits, one for r32/33/34 rear end, one for r31, starting at $350

-turbo s13 sway bars, make your factory non turbo shell handle properly (huge difference) $50 each

-ae86 project 5000-8000 depend on spec

-rb25 motor package $2000

-rb25 clutch package

-silvia/skyline kaaz 2 way diff $800

-s13 welded diffs starting at $100 exchange

-silvia driveshafts from $50 each

-s13 tail lights, factory and factory tinted $50 a pair

-180sx and s14 clear bumper indicators $40 a pair

-180sx factory tail lights

-ca18 parts and ca20det stroker kit

-4age clutch kits new and used

-4age quad throttle kits

-4age billet cam/crank/water/alternator pulleys

-4age trd head gasket $100

-ecus for ca18 and sr20

-sr20 crank- perfect

-sr20 block- perfect factory size bores

-sets of sr20 rods

-sr20 tomei 87mm forged pistons used but perfect condition $200

-sr20 used perfect condition 9.5:1 pistons

-sr20 s14/15 vipec ecu $1200

-sr20 injectors 370s, 444s and 550s instock $50 $200 $350

-available as a kit or seperate sr20 parts above

-turbosmart fpr800 fuel reg with fittings $150

-rb26 forged pistons new,custom, $1200+

-rb26 crank, long drive fitted, storage surface rust suit clean and polish $400

-rb26 rods factory and forged

-rb26 n1 block needs sleeve in one cylinder

-sr20 gti-r turbo suit rebuild (or use for .86 rear housing)

-gtr/rb20/25/sr20 turbo actuators

-s13 knuckles $150

-s13, 14, 15 and r32 33 and r31 front lower arms instock

-s13/4/5 factory rear arms and one s13 subframe instock

-sr, ca, rb factory radiators instock starting at $40, aftermarket also instock starting $200

-thermofans, new ba falcon, modied for sr20 bolt on, $150

-clutch fans and hubs, factory and aftermarket for all skyline and silvia instock

-rb20, s13, s14 power steering pumps instock starting $80

-rb20 and rb25 r32 engine mounts

-s13 manual gearstick surround unbroken $25

-slip on and bolt on wheel spacers 4 stud

-cam and timing covers rb20, rb26, rb25, ca18 and sr20 s13 in stock

-misc used but good pod filters $10 no pics

-180sx drivers front guard $100

-180sx type x bumper with reo and foam no lights slight damage $300 (less than half the going rate)

Rb26 below

R34 n1 rb26 block. Needs sleeve in one cylinder, onced sleeved will be stronger than factory. $500 Rb26 crank from r32, fitted with collar. Needs a clean and polish from storage. $400

Custom made pistons to take factory rings, je. Various compression ratio. Nothing less than 1200 a set cost double to make

New genuine rings also instock for extra

Set of rb26 rods with arp2000 bolts

Think I have a set of jun rb26 rods can't remember If sold or not

Rb26 r34 n1 nismo adjustable cam gears $150

Rb26 cams, factory and new tomei type b

Rb26 new air flow meters

Rb26 nismo gmax twin plate clutch no friction discs

Rb26 harmonic balancers r32 r33 Nd r34

Power steer pumps r32 33 34

Gearbox rebuild parts 33 and 34

Upgrade nismo input shaft r34

27 spline rarer than 24 from memory

Rb26 cam covers

Nismo thermostats

N1 water pump I think I have one left

Tomei head gasket kits

Nitto headgasket kits I think I have one left

Factory r33 exhaust manifolds

R34 n1 fabricated at nismo dump pipes

Rb26 custom fabbed dumps also

Stock injectors also

Gearboxes

4 sr20

1 rb20

1 rb30

1 r32 gtr need synchro on 3/4

Heaps more stuff, need money for 370z drift car

Hey boys and girls I'm chasing the little part where the oil pressure sender screws into on a 26 as the thread in mine is nearly cactus and Nissan dont make them anymore.

Part looks like this

post-58307-0-55679800-1363918789_thumb.jpg

And goes onto this.

post-58307-0-75705500-1363918827_thumb.jpg

Yeah I tapped it with a 1/8th bit but the thread is only about half there. Any ideas on where to get the reducer fittings from? I also want one to go in my trust/greddy oil cooler sandwhich plate but havent had any luck finding anything so far.

  • 2 weeks later...

If your using a r32 radiator a r32 item is the go. I don't believe that a r33 radiator fits properly. And as far as 25 in a 32 most stuff like the fan line up the same.

And I have a r32 shroud if you want it.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...