Jump to content
SAU Community

Alarm/central Locking On R33

R33_RB25

By R33_RB25,
in Car Audio & Electrical

 Share

Recommended Posts

R33_RB25 Contributor

R33_RB25

Posted
Posted

I am thinking of putting an alarm into my r33, and i have done some research, for the central locking part we will need an actuator for the driver side,

and i noticed that most of the alarm systems dont come with an actuator, does that mean i have to get my own one?

and is there any wiring diagram for r33 here?

cheers

Link to comment
https://www.sau.com.au/forums/topic/364304-alarmcentral-locking-on-r33/
Share on other sites
  • 3 weeks later...
Rilez Newbie

Rilez

Posted
Posted

yes your car needs a door motor on the drivers door you can buy a single door motor kit from jaycar and can be used on most alarms i do hundreads of skyline alarms in sydney any questions just ask me

alright if you've seen hundreds of skyline alarm installs maybe you, or anyone could help me with my problem.

i was trying to install extra LED lights on to the light that comes on around the key ignition thingy when you unlock the car and turns off after approx 10sec of shutting the door (not really sure what thats called) but i think i shorted it but without blowing a fuse... theres still a little bit of power going to the light but not enough to fully power it or any others.

and i have no idea what i've done.

sad face.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

what version 33?

and for the fellow that's done hundreds of cars - ABN or employer please..

I can vouch for hundreds of them - been working on these cars for the past 11 yrs.

if its a S2 then you have probably popped the smart entrance module and that's not a good thing.

  • 4 weeks later...
oakleigh Newbie

oakleigh

Posted
Posted

Adding an actuator to the drivers door is one option but a poor one. The angle at which you need to mount the aftermarket actuator makes it unreliable. The actuator rod that conects to the original door locking rod will snap off after a while.

A beter option is to tap into the existing system. The car already has actuators in both doors and they work well. The trick is to feed a signal into the central locking module from the new alarm. I think I can figure out the connections if I had a circuit diagram for the R33. I have been searching for ages now for this circuit diagram, but no avail. The "chassis" manual for the R33 is rare and no electronic version seems to be available online. Those who have hard copies are keeping the manual close to their chess!

Carbon 34 Grand Master

Carbon 34

Posted
Posted

chris the compliance shop that did my car wired the drivers convience module out of the loop, I had to open up the drivers door to find the hack they did to over ride it. pm for how they did it.

returned it to normal now . also the light around the key surround is easy to fix. I changed mine to Blue LED, looks way better now.

AAA34T Community Regular

AAA34T

Posted
Posted

Adding an actuator to the drivers door is one option but a poor one. The angle at which you need to mount the aftermarket actuator makes it unreliable. The actuator rod that conects to the original door locking rod will snap off after a while.

A beter option is to tap into the existing system. The car already has actuators in both doors and they work well. The trick is to feed a signal into the central locking module from the new alarm. I think I can figure out the connections if I had a circuit diagram for the R33. I have been searching for ages now for this circuit diagram, but no avail. The "chassis" manual for the R33 is rare and no electronic version seems to be available online. Those who have hard copies are keeping the manual close to their chess!

done heaps of r33s and only ever seen 2 with a factory door motor in the drivers door and you can put the aftermarket door motor dowm the bottom and it lines exactly up strait and have never had any problems or had to go back and fix any they all have a factory switich not motor even 32 33 and all 34s have a factory motor exept n1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...