Jump to content
SAU Community

Engine Swap.

ye.808

By ye.808,
in Engines & Forced Induction

 Share

Recommended Posts

ye.808 Collaborator

ye.808

Posted
Posted

I currently have a r32 gts-4 manual, and want to put an rb26 into it. Ive searched through the forums and the topics were quite old, so would like to ask some advice on going about it. Is it worth doing these days or would it be better to just buy a r32 gtr? My situation would be, if i were to put an rb26 into it, i would go to a workshop.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/
Share on other sites
GTScotT Grand Master

GTScotT

Posted
Posted

isn't that rb25de as is? Uses Rb20 injection etc???

Logic tells me turbo it and save big dollars, then slam stocky gtrs with it.

just confirm what motor u have and when i get to a pc I'll comment further...

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5828179
Share on other sites
DR 32R Rising Star

DR 32R

Posted
Posted (edited)

I'm doing the Stagea swap. All wheel drive rb25, I agree with giving thought to a r 32 GTR. There is a lot of satisfaction in doing a swap, rb26s are getting cheaper. If you did both a rebuild and a transplant it will add up quickly. If you buy a 32gtr you could also be sorting out a motor and wear and tear any way. Most people will tell you GTR. I still think a gts4 with swap is interesting. With you Vic address have you looked at legalities of the swap? If you're buying a GTR why not get a later model 33 or better still 34 and just service it, a 32 is often a rebuild/restore etc.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5828217
Share on other sites
GTScotT Grand Master

GTScotT

Posted
Posted

Id honestly love to have a GTS4 over a GTR, there is a certain element of surprise that allures me.

Personally, having done the RB20 and 25 things in the past, Id probably try to pick up the shortest ratio diff I can and keep the RB20. Having a good turbo on it that will max out at something like 230rwkw would make for a very fun and respectable car.

If I had to have more, I would buy an RB25 donk and retune the exact above setup with non vct cams. That would unlock about 20kw more and all bolt back into place.

Doing an RB26 is probably going to set you back atleast 5k more than the above and will still be in stock trim... Only just faster than above if not at all.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829466
Share on other sites
DR 32R Rising Star

DR 32R

Posted
Posted

The GTS4 gives you the cheapest all wheel drive chassis, which you own already. This is an example of the type of Stagea set up you could buy. An upgrade turbo or highflow turbo, could see you performing better than a stock tired GTR. Potentially you could have the GTR performance envelope, and more money in the bank.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=370511948278&ssPageName=STRK:MEWAX:IT

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829509
Share on other sites
DR 32R Rising Star

DR 32R

Posted
Posted

get a neo rb25 instead, better than half the thrashed rb26s out there

ultimately just sell the car and buy one with everything already done to it

He would have to track down a Stagea Neo all wheel drive RB25, agree better cylinder head and rods.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829858
Share on other sites
dorifticon Community Regular

dorifticon

Posted
Posted

I think the main point from the OP is that he'd be paying a workshop to do it.

Honestly, you may as well hand over your wallet, bend over and drop your daks.

I really can't see how you are going to come out ahead - $$-wise, kw-wise - getting a workshop to do the conversion. They charge for every hour they spend.

Even if you were doing it yourself in your shed it would be questionable. At least then the risk would be your time rather than $$.

If you are dead set on getting a GTS-4 conversion, wait for one already done to pop up, it's bound to happen.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5830042
Share on other sites
DR 32R Rising Star

DR 32R

Posted
Posted

If he buys an r32 gtr, a move which makes sense to me, when the engine has a problem, (quite often clutch electricals, ATESSA, suspension as well), where will he go? A workshop as many on this forum do. He could remove the existing engine and donor engine, with friends and an engine crane source parts, to control his costs.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5830210
Share on other sites
GTScotT Grand Master

GTScotT

Posted
Posted

Do whatever makes you happy, whatever you want more. Nothing is cheap, yet I would be damned if I could not beat a GTR with a GTS-4 dollar for dollar. Performance and reliability as said above.

GL

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5832626
Share on other sites
DR 32R Rising Star

DR 32R

Posted
Posted (edited)

If you picked a sensible power figure above a stock GTR, I'm sure I would get there more cheaply starting with a gts4, than buying a gtr and upgrading it. Similar to the post above.You already have a GTR chassis with an unflared body. Consider the nz gts4 below.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5832703
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      Fuel Pump Control Module & Dropping Resistor

      By EndZee · Posted

      Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • Duncan
      M35 Brake caliper replacement

      By Duncan · Posted

      You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Duncan
      Most women will agree that parking is the most taxing part of driving

      By Duncan · Posted

      Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • Duncan
      NC MX5

      By Duncan · Posted

      On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
×
×
  • Create New...