Jump to content
SAU Community

Help With R34 Gtr Wheels

livewire
 Share

Recommended Posts

livewire Experienced

livewire

Posted
Posted

Another question guys lol. I've had new tyres fitted to my R34 gtr wheels but they've put those little balancing weights around the wheels near the outsides And they stand out like dogs balls and look shithouse. Are they able to put them at the inside of the rims rather to hide them or do they even need them being factory R34 gtr wheels going on an R34 gtr??? Just not happy with the look of them at all

Link to comment
https://www.sau.com.au/forums/topic/366518-help-with-r34-gtr-wheels/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

what sort of rims they are and what sort of car they are going on means bugger all (they are done off wheel and tyre balance, not just wheels). as for whether they can put them on inside the tyre, well they could, but since they balance the tyre once it's already on the rim, that makes it a bit more difficult, plus the fact that if one comes unclipped or the glue lets go then it will probably puncture the tyre, so not a good idea.

livewire Experienced

livewire

Posted
  • Author
Posted

Yeah they are only stick on ones but what I am saying is they've placed them near the lip of the rims between the spokes so they are highly visible when looking at the wheels and it looks shit so I'm trying to find out whether I can ask them to move them (recess them) deeper so travel they're not so noticable.

mad082 Grand Master

mad082

Posted
Posted

No no, I don't mean inside the rim between the rim and tyre lol. I mean can they put the weights towards the back of the rims not right at the outside edge near the spokes where they are visible

may possibly come down to where the rim is out of balance, but ask them if they can put them behind the spoke line.

Daleo Grand Master

Daleo

Posted
Posted

+11ty!:rolleyes:

The weights should be on the machined barrel of the rim, BEHIND the spokes. You can even put a little touch up paint on them if you want to hide them further.:ph34r:

Sticking the weights in the apertures of the spokes, right on the lip of the rim is just not good enough.

Tell them the rims are NOT going on a Commodore :whistling: , and they need to lift their game...

Goombeh Collaborator

Goombeh

Posted
Posted

Yeah, shouldn't be a problem, they did this to mine too, right between the spokes, pretty half rsed if you ask me.

Anyway I simply marked the posi, cleaned the inner rim, moved the weight 10mm or so in with some new double sided tape, and perfect. Has not impacted the balance at all. Although I believe for the absolute perfect balance, a machine will tell you whether the weight would be more effective on the inside or outside of the rim. But when it's between the spokes, it's not really at the outermost edge of the rim, so I would be very surprised if it changed anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...