Jump to content
SAU Community

Recommended Posts

firstly i would say check ALL OVER THE CAR for a pink / green / purple plate etc etc.. check in the door jambs on the passenger door..

if it's still not there i would be inclined to say that no, you will definitely not be able to get that vehicle complied with an RB26. or possibly comply it at all...

that said - i see you're from queensland - and from what i see over there, it's pretty much anything goes if you slip em a XXXX!!!! ahahaha

firstly i would say check ALL OVER THE CAR for a pink / green / purple plate etc etc.. check in the door jambs on the passenger door..

if it's still not there i would be inclined to say that no, you will definitely not be able to get that vehicle complied with an RB26. or possibly comply it at all...

that said - i see you're from queensland - and from what i see over there, it's pretty much anything goes if you slip em a XXXX!!!! ahahaha

LOL yer wish it was that easy

i looked every were its like some one half tried to comply it cos its got the side intrusion bars but just no paper work and no green plate

no wonder it was cheap

are you brissy based? if so I can probably help in a way.

whn you bough it was it registered at all or had it been through registration?

do you have a chassis number at all?

are you brissy based? if so I can probably help in a way.

whn you bough it was it registered at all or had it been through registration?

do you have a chassis number at all?

i'm in central qld

it hasn't been registered no aus vin number just the jap one

ok ,

when you bough it did you get ANY of the import paperwork with it?

if so contact a RAW that can comply your type of car and tell them the story. www.raws.com.au will give you a starting point.

if NOT then you have a track pig only. it cannot be registered here.

My car is currently registered, but the compliance plate has been lost from a re-spray and re-build. now the previous owner is being a C&*T and doesnt want to help me in any way. I dont have any import papers, just the new aussie vin has been stamped on the drivers strut tower. Is there anything you can suggest Chris for me to get a replacement so I can get a roadworthy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...