Jump to content
SAU Community

R33 Interior Parts, Seat Belts, Boot Interior, Amp

RBSkyline
 Share

Recommended Posts

RBSkyline Enthusiast

RBSkyline

Posted
Posted

Hey guys I have some interior parts from my 93 S1 R33 GTS-T. I have no idea what they are worth so just put an offer in, I just want this stuff gone. for some reason it wont let me upload photos but I am happy to MMS them. My number is 0401 321 564 be easier to TXT me. Location Brisbane Southside.

*** Rear side interior panels including the front seat belts both in excellent condition (will not seperate them) Have both sides

*** Rear pillar parts that the rear seatbelts run through including the rear seat belts (will not seperate them) Have both sides includes the handles also (drivers side has a small crack where it meets near parcel shelf) these items are still on the car but will be off shortly

*** Boot interior good condition, missing most the clips and the plastic piece that runs across the top

*** Sony Xplod 250W AMP. Came with my car but I am stripping the car and turning it into a track car so this is not needed. I am not into my audio equipment so I know nothing about these items and I do not know what they are worth.

It says on it 2/1 channel XM-502Z has mounting plate to go in a R33 near battery.

Please make an offer and I can MMS photos

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...