Jump to content
SAU Community

Recommended Posts

i know i should be severly beaten for not knowing this but i'll ask anyway, im looking for a couple of turbos for a new project im looking at 2 t28 but someone sugested a skyline turbo. can someone tell me what kind of turbo the skylines run? and im guessing the gtrs are runing different 1s to teh gts t

lucas

Link to comment
https://www.sau.com.au/forums/topic/368255-skyline-turbo/
Share on other sites

i know i should be severly beaten for not knowing this but i'll ask anyway, im looking for a couple of turbos for a new project im looking at 2 t28 but someone sugested a skyline turbo. can someone tell me what kind of turbo the skylines run? and im guessing the gtrs are runing different 1s to teh gts t

lucas

GTR's run with twin T28 Garrett turbos.

So you can say they are 'Skyline turbo(s)'.

Link to comment
https://www.sau.com.au/forums/topic/368255-skyline-turbo/#findComment-5873899
Share on other sites

thats 1 sexy gtr skyline dam im jeleous

:laugh:

It's tuning house, Garage D's R32 GTR from UK.

Wish it was mine.

Mine looks similar but with white wheels and no spoiler.

Here are the R32 and R33 GTR Turbine Specs if that helps:

Compressor Housing: T3

Compressor Wheel: T3

Compressor Wheel (mm) 42.5 - 60.1

Compressor Trim: 50T

Compressor A/R: 0.42

Turbine Housing: T25

Turbine Wheel: T25

Turbine Wheel (mm): 41.5 - 50.5

Turbine Trim: 62T

Turbine A/R: 0.48

Link to comment
https://www.sau.com.au/forums/topic/368255-skyline-turbo/#findComment-5877279
Share on other sites

unless it is only around 2.6L then the rb26 turbos will be WAY too small for a v12, unless you plan using 4 of them. you need to find turbos suited to the engine size you have. 2 rb25 turbos may possibly suit, but it depends on how high the engine revs.

Link to comment
https://www.sau.com.au/forums/topic/368255-skyline-turbo/#findComment-5879998
Share on other sites

Two GT30 sized turbines at the least! Smaller than that and you'll get restrict the exhaust too much, then EGTs will be high too. You'll have to retard the ignition and so won't make much power especially at high rpms.

Twin gtx3071s *drool*

Link to comment
https://www.sau.com.au/forums/topic/368255-skyline-turbo/#findComment-5880074
Share on other sites

bmw 5l, ive been on the bmw forums where this this is comon pratice and everyone say either t28s or gt3040 depending on what power i was looking for.someone did suggest quads hahahaha, not sure what vehical its going in yet something old problaly

Edited by jimbothepunk
Link to comment
https://www.sau.com.au/forums/topic/368255-skyline-turbo/#findComment-5881905
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...