Jump to content
SAU Community

Recommended Posts

Finally got to see my baby! Bit dirty but that was expected after sitting in Japan for 3 months and time on the docks. Found small scratches that need cut & polish, rusty bonnet hinge, a bit too low, missng front bar clip and loose grille but otherwise really nice interior and exterior! Now just waiting for mechanical inspection and bloody Regency...they sure do take their time with paperwork!

Can't wait to have her on the streets of Adelaide!!!

Link to comment
https://www.sau.com.au/forums/topic/36915-my-car-has-finally-arrived/
Share on other sites

It's an 89 BNR32 running cost so far $21K...

Extras that I need:

No compliance yet probably $1.1K

Registration and stampduty ~$1.2K

Tyres...$1.2K

Any maintainence done as well but it "sounds" fine from my mechanicaly non-inclined ear :D

nice car ecenshu. Ahh so that r32gtr i saw at pvp import was yours. Looks very nice and mean, didnt have a close look but was definately low. I was there as my gf had her car serviced. Also so a very nice silver gtr of the same variant sitting in the back of the workshop.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...