Jump to content
SAU Community

Recommended Posts

Why not? surely there must be a shitload of RB engines out there that are running reground cranks?

Yeah for sure there are a shitload around. I have rebuilt many engines with ground cranks but you NEVER grind a crank unless you have to. You don't just grind them to get the crank to a specific size/clearance. Usually they are ground when the crank is bent after an engine failure but can also be due to journal damage in some cases.

really? how deep is the nitriding, and how much is ground off for oversize bearings?

2 thou deep is usually the case for most nitriding but it can go deeper. For every 2thou deep you go, the journal size grows by approx 0.00005-0.0001. 10 thou is is what is taken off for a grind

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

could'nt you have it re-nitrided

^ Thats what i was gonna say,im sure on top of re nitriding there is also cryogenic treatment that will strengthen the crank far beyond factory specs,new cranks are fricken expensive and then you have to piss fart around getting bearings for them? . . pass

new cranks are not that expensive <$1500. when doing a build with top $ parts (pistons rods etc) it's often worth buying a new crank for piece of mind. no point having all good gear with a bent crank...

^ Thats what i was gonna say,im sure on top of re nitriding there is also cryogenic treatment that will strengthen the crank far beyond factory specs,new cranks are fricken expensive and then you have to piss fart around getting bearings for them? . . pass

you're worried about 'piss farting' around with getting bearings (which are available in 5 minutes at most good auto suppliers or your engineer) but you don't seem to think Nitriding and cryo treating a crankshaft isn't just as much of a stuff around?

Can take them up to 2 weeks to nitride and cryo a crankshaft and even then you have to get it checked and rebalanced after the treatment is done as you are changing the structure of the metal and adding meterial.

Keep it simple - old crank/new crank who gives a shit, new ACL race series bearings, build engine.......skids - no piss farting around at all

Interesting information put there.

But picture this, you live in a third world country where the engineering standards have never been good, they cant even skim a head properly let alone grind/straighten a crank shaft, and then there is still boring the block and honing, which the honing part i can do but boring cannot be done they are useless, and to make matters worse tunnel boring or line boring block crank journals and head cam journals has been tested here and never comes back good enough to build a high performance engine.

So essentially this is ,my build

New block Factory spec N1

New pistons Factory Spec N1 with N1 rings

New rods Tomei cheaper than factory Rb26 Rods

A set of Acl bearings mains and Big ends X size with 0.0001" extra clearance so the crank can flex a bit

New set of oil piston sprayers

And the rest i already have

Ati damper pulley

Tomei Baffle sump

Tomei high flow oil pump

Tomei head restrictor 1.2mm

Ported and polished head

Viton Valve stem seals

Nismo twin plate clutch with flywheel

New head bolts from Nissan

Greddy 264 Degree cams intake and exhaust with vernier pulleys

Magnetic drain plug and magnetic Oil filters to be safe on the new build

i dunno if there is anything else i missed out but never the less im not aiming for Big hp, im just building a good reliable engine.

So if im getting factory spec block and factory spec pistons to suit it should be good to go ?

Interesting information put there.

But picture this, you live in a third world country where the engineering standards have never been good, they cant even skim a head properly let alone grind/straighten a crank shaft, and then there is still boring the block and honing, which the honing part i can do but boring cannot be done they are useless, and to make matters worse tunnel boring or line boring block crank journals and head cam journals has been tested here and never comes back good enough to build a high performance engine.

So essentially this is ,my build

New block Factory spec N1

New pistons Factory Spec N1 with N1 rings

New rods Tomei cheaper than factory Rb26 Rods

A set of Acl bearings mains and Big ends X size with 0.0001" extra clearance so the crank can flex a bit

New set of oil piston sprayers

And the rest i already have

Ati damper pulley

Tomei Baffle sump

Tomei high flow oil pump

Tomei head restrictor 1.2mm

Ported and polished head

Viton Valve stem seals

Nismo twin plate clutch with flywheel

New head bolts from Nissan

Greddy 264 Degree cams intake and exhaust with vernier pulleys

Magnetic drain plug and magnetic Oil filters to be safe on the new build

i dunno if there is anything else i missed out but never the less im not aiming for Big hp, im just building a good reliable engine.

So if im getting factory spec block and factory spec pistons to suit it should be good to go ?

You email engine builder in a 1st world country and say 'hey, build me this' and wait for an engine to arrive in your letterbox

Don't make me revive that thread/s.

?

I'm merely pointing out to him that it's often not worth the risk to build it locally if the standard is so poor.

There are plenty of good engine builders in Australia and engineering standards are extremely high as long as you use Chilton Engineering 07 33911672 :P

Look i understand that you guys want me to get a engine built by a good builder, but im tight on budget and have two hands half a brain and two eyes.

i also have the ability to learn and have learnt alot since we last spoke .

I have also built two Rb 20 engines and one 4age engine and have done this with some fair amount of investigation and downloading of clearances etc.

I just wondered why i was told to use a standard bearing size on all the builds i have done so far and needed some clarification.

So i dont want to pay some one else to build an engine i want to build.

We have been down this road and i dont want to even start the topic again either.

Lets put it this way ... im excited to check measure and build an engine as nice as a rb26dett.

And it wont be the last engine i build infact its the start of many more to come i want to build my next gtr32 engine as well to a serious spec.

And then if im going to be boring blocks and needing engineering done i will get a company in Australia to build and machine for me then import it back and run a beast of a car.

But at present i want to build this engine for this car .... note build this engine and this car being the most important words.

Its an aspiration, please dont flame me and put me down i think enough of that has happened, i have often walked away from the forum feeling like an idiot.

So to cut out the machine work, a new block, new crank and new rods will be purchased and ring gaps checked, bearing clearances checked and tested etc.

Then the motor will be assembled and run .

I need guidance not insults and being told where to send my sub assembly etc etc.

I even thought if fitting a Nitto crank 73.7mm crank with rods and pistons and even considered a sub assembly built by a company chosen by Nitto performance.

But there is not satisfaction there, especially for the guys who love building engines their pride is in building checking and assembling a complete motor and then saying, i did that i assembled it and i made it run .

Please dont take offence.... no one should take offence.

Im almost ready to order the parts, then assembly takes place.

No offense taken by anyone I'm sure, but please understand that no matter how many engines I have built, if my engineer did anything short of a perfect job in his department, then I would not still be in business.

With you saying that getting the engineering processes done well locally is extremely hard, I would say you are missing one of the most important parts of the puzzle.

No one here would be able to spare the time to teach you how to engineer and balance your engine, then assemble it (although you seem to already have that part sorted - it's only a small part in the whole process....the assembly)

Good luck with your build though, the saying is true - the poor man pays twice

As long as your piston to bore clearances are good, pin to little end clearance is good and the clearances for all the bearings are done, I'm sure you will be absolutely fine. Just make sure you check it all and don't cut corners

new cranks are not that expensive <$1500. when doing a build with top $ parts (pistons rods etc) it's often worth buying a new crank for piece of mind. no point having all good gear with a bent crank...

$1500 not expensive?please tell me where you work,i want a job on your salary!:thumbsup:Ps even new cranks CAN be slightly bent

$1500 not expensive, as BB said

Def need a job with you guys!

Im not saying that $1500 isnt much for me personally, but some out there who spend the big $$ on parts for rebuilds then a new crank is the least of their problems. Go look in the for sale section and theres a few threads with parts in there like $13K for a block or $11K for a head...add each part of that into a whole setup and the $1500 for a crank suddenly seems insignificant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...