Jump to content
SAU Community

Recommended Posts

R32 GTR 1991

Selling for a friend. Matt can be contacted on 0411 781 741

Regrettable Sale - New P Plate Laws. im not allowed to drive a turbo car anymore

Makes a really responsive and Reliable 270Rwkw on very safe tune running 18Psi. I had -5's and didnt like the lag.

Car made 320rwkw with then running 18Psi but it feels almost faster now having so much more time in boost.

will easily make more power with more boost, air flow meters amd cams.

GT-C Volk 18x9's all round with custom GTR offset

Built Motor (done about 2,000 k's since build)

Chemical clean all parts, full machine,clearance and blueprint spec, ACL comp bearings, JE forged piston kit, H-beam rods,

MLSR steel head gasket, oil restrictors, genuine nissan gasket set, tensioners, Recon head, complete assembled from sump to rocker covers.

all new hoses

new genuine thermostat

new water pump

new timing belt

nismo radiator cap

new battery

new heater core

regassed Air conditioner

nismo diff bushes

cradle spacers (pineapples)

600cc injectors

nismo plugs

Garret 28/60 -7's

Apexi Power FC with Hand Controller

Full 3" Kakimoto Exhaust

Blitz 4stage Boost Controller

R33 GTR Crank

N1 Oil Pump

Momo Steering Wheel + Gear Knob

'Top Secret' Carbon Fiber Dash/Console Surround

Custom Leather Interior

Tomei 310km/h Dash Cluster

New slotted rotors all round (DBA)

Extreme heavy duty motor sport clutch

Koyorad radiator

custom buzzer/Warning light (oil pressure, coolant level, water temp.) better then trying to watch gauges whilst driving.

Central Locking/Alarm

Good stereo (alpine headunit, Focal Splits and rears, Basic sub/amp setup)

Baffled sump

Bosch fuel pump

Always has run fully synthetic oil

Always kept off the limiter

Never been launched

Brand new tires

Im sure there is things I have missed. Photos do not do the car justice.

Car owes me 50k. have receipts for the last 15k spent a month ago

regrettable sale, but i cant legally drive it for the next 2 years

Im after 25k ONO and im aware im asking a high price but its one of the best 32 GTR's in SA.

Has been featured in HPI.

The other option is 22k ONO bring your own wheels and i keep the carbon dash, sub and cd player.

There's other 32 GTR's on the forums for 20-22 but they arn't forged motors, nor do they have amazing wheels or interiors. Priced to go.

If your not interested in buying or giving positive comments don't post, don't send me a PM as im not on the forum often, do text or call me. Thank you.

post-86237-0-25284700-1310274295_thumb.jpg

post-86237-0-92951000-1310274422_thumb.jpg

post-86237-0-30143600-1310274434_thumb.jpg

post-86237-0-78119800-1310274485_thumb.jpg

post-86237-0-73349200-1310274517_thumb.jpg

post-86237-0-16715300-1310274585_thumb.jpg

Edited by SNIPER32
Link to comment
https://www.sau.com.au/forums/topic/370504-1991-r32-gtr-sniper-mint-condition/
Share on other sites

  • 2 weeks later...

Still for sale, only dreamers with no money at this stage. I can see there is cheaper 32 GTR's on the forums making similar power but no forged motors, no amazing wheels, no mad interior. This car is the complete package. Buyer will be as happy to own it as i have been. :whistling:

All the required oil issues have been solved with oil restrictors etc when it was built, Most 32's have issues with oil pump and crank, thus both got upgraded.

Try and sell ya cars guys. Keen to sell it asap. Inspections welcome. :) Will not disappoint :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...