Jump to content
SAU Community

Recommended Posts

Yeah you can roll a bogged guard...gotta be very careful that's all, and be prepared to touch up. Paint can crack anyway without bog there. If guard roller is good it'll only crack in the part that gets rolled and then you can't really see it.

Mine needed rolling front and rear FYI

But I'm running 265's on the back and 235's on the front.

They were only just rubbing, rears rubbed when going over harsh bumps and fronts rubbed when turning

Car1.jpg

Car2.jpg

Camber.jpg

thats supposedly 2 degrees of rear camber (According to pedders) looks like more but

Edited by 89CAL
  • 2 months later...

sorry to bring this thread back up, how will 17x8+33 and 17x9+37 look guys? i just want something to sit good without needing spacers, i am also going to have camber arms on the rear and if anything ill get the front rolled

these are the specs they have in stock as im most likely going through this dealership, its giving me a headache trying to work out what to get :wacko: i just dont want something to sit inside my guards to much

The 17” D1R’s come in an 8, 9, 10 option.

17 x 8 is in an +33 offset.

17 x 9 comes in +37, +17 and -4.

17 x 10 comes in a +15.

The matt black in 17 x 9 +17 and 17 x 10 +15.

See my previous post for side pic. it needed the guards rolled but thats all, no camber arms.

2011090421454130.jpg

oh yeahh i see i might get 17x9+17 all round then. all would the same size all round look shit?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...