Jump to content
SAU Community

Recommended Posts

Kyle , I have all the photos and receipts from when i bought the car from beer baron all up this engine has done 42, 000 kms from when it was installed as brand new engine , if you did buy it all this information will go with the engine . Aaron.

yea sweet well like i said i gave andrew a call and the motor wont be checked until next week so im hoping it will be given the thumbs up and ill come get it next friday :)

Kyle , I have all the photos and receipts from when i bought the car from beer baron all up this engine has done 42, 000 kms from when it was installed as brand new engine , if you did buy it all this information will go with the engine . Aaron.

Hey Aaron, I thought I had passed all the stuff on. I was sure you'd keep it all :) Glad to see you on the forum.

If there is anything I can do for you mate, please don't hesitate to ask. So sorry to hear you were involved in a crash through no fault of your own. I know you treated that car very well and i'm sure the engine has plenty of life in it yet. You have the receipts so you know what that engine cost so I hope you get a good price for it. It was a great set-up for a street car. The car itself was probably the nicest R32 I've owned and i've owned about a dozen. I'd say it's as nice or nicer than the one I've got now which I plan to keep for a long time.

As to gtr_23qu's question on power the engine builder was told it needed to handle 600hp but honestly a decent stock motor will handle that. The base N1 Nur engine is supposedly rated to 600hp anyway but this one was blueprinted and has a 1.2mm tomei head gasket fitted. I would be comfortable pushing it to 400kw atw+ for a street car. It has a few key bits that will enable it to handle some decent boost and power.

yea sweet well like i said i gave andrew a call and the motor wont be checked until next week so im hoping it will be given the thumbs up and ill come get it next friday :)

You dont know how much i want for it yet , you might not want it then :)

lol, well I know what it cost and it's not cheap. N1 block, N1 oil and water pumps, ported head, N1 pistons, tomei head gasket, tomei timing belt, all blue-printed and all other bits are brad new down to ever last nut/bolt/seal whatever. a lot more than what is replaced in the average rebuild. hope you get good money for it Aaron. :)

lol, well I know what it cost and it's not cheap. N1 block, N1 oil and water pumps, ported head, N1 pistons, tomei head gasket, tomei timing belt, all blue-printed and all other bits are brad new down to ever last nut/bolt/seal whatever. a lot more than what is replaced in the average rebuild. hope you get good money for it Aaron. :)

Hey Rich , i have already told him a price so it looks like someone is getting a bargin at this stage >_<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...