Jump to content
SAU Community

Recommended Posts

Hey guys

A few months ago i drove in a massive storm and was going about 100km on the free-way. When i got home my hood was loaded with dried up water marks which was caused by the heat of the engine to evaporate the water leaving behind chemicals. I tried washing the hood, waxing, rubbing it with vinegar, yet none of these have ever worked. I haven't tried buffering yet cause i don't have a buffer at home. Does anyone know how to remove these water marks?? cheers!

Edited by Deza3000

Hey, thanks mitch, ill go buy that and give it a shot =)

do you know where i could find this??

Id buy it straight from waxit.com.au with a 12.50 flat rate shipping get some shampoo and a chamois or something also.

Regards,

Mitch

  • 1 year later...

Hey guys similar situation to the first post, spewing because I clay barred, body cleansed and waxed (Bowdens Own Range) my wifes car 2 weeks ago, sometime in the last week its been caught in some rain and all the dirt/dust that settles on the car after not being wet for sometime left dirty water marks all over the car.

After washing it this morning, I found that the outlines of the watermarks were still on the paint, went over it with a quick detailer after washing/drying but no difference.

Would the Duragloss Spot Remover recommended above be enough to remove these or do people suggest that I'll need to go over with some sort of polish? If so, any suggestions?

I've attached a couple of pics, thanks.

post-17881-0-01177000-1358202390_thumb.jpg

post-17881-0-04389000-1358202431_thumb.jpg

Hey guys similar situation to the first post, spewing because I clay barred, body cleansed and waxed (Bowdens Own Range) my wifes car 2 weeks ago, sometime in the last week its been caught in some rain and all the dirt/dust that settles on the car after not being wet for sometime left dirty water marks all over the car.

After washing it this morning, I found that the outlines of the watermarks were still on the paint, went over it with a quick detailer after washing/drying but no difference.

Would the Duragloss Spot Remover recommended above be enough to remove these or do people suggest that I'll need to go over with some sort of polish? If so, any suggestions?

I've attached a couple of pics, thanks.

got that same shit on my car, more noticable on the roof, i had previously tried hand polishing without success

I had a similar problem with my celica couple years ago. I used heavy duty wash (I think brand was polyglaze) and then cut (kitten cutting compound- red can) then polished and waxed. The cutting and polishing stage is when these marks dissapeared.

This forum has taught me that waxing is not the solution to swirl or water stain or bat crap marks. The wax is only a sealant which protects and shines the surface.

  • 2 weeks later...

Thanks for the replies, yes I agree Gary, I went back to step one with a paint cleaner then went over with a light polish and finally a sealant then a couple of coats of wax. I visited Wax It Car Care in Tullamarine and they were very helpful but said often it requires paint correction.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...