Jump to content
SAU Community

Recommended Posts

sparkplugs won't cause detonation, they can but it is highly unlikely in your situation, it almost certainly CAS base timing is advanced, you are not running 98 octane fuel, or it is a fuel issue and is leaning out.

Get it on a dyno and diagnose the issue, don't keep driving it or you WILL destroy the motor.

was hoping it was the spark plugs in my mind but have a feeling its not. plus when its idling and about to move forward in 1st.... i can hear a belt squeek in a way, been testing it while holding the brake and letting the clutch out i can hear it more......... its never done it before til this pinging noise.....

this car is my daily car, be hard for me to get around.......... imo ....its really annoying :)

sparkplugs won't cause detonation, they can but it is highly unlikely in your situation, it almost certainly CAS base timing is advanced, you are not running 98 octane fuel, or it is a fuel issue and is leaning out.

Get it on a dyno and diagnose the issue, don't keep driving it or you WILL destroy the motor.

+1 have a look at the CAS position , see if someones been messing with it.

.. imo ....its really annoying :)

having to replace the motor will be even more annoying, do not rev it past 4k and no boost until this is solved, I don't think you realise how serious this is. 10 seconds on full boost with sustained detonation is enough to melt ring lands.

having to replace the motor will be even more annoying, do not rev it past 4k and no boost until this is solved, I don't think you realise how serious this is. 10 seconds on full boost with sustained detonation is enough to melt ring lands.

yeah! what he said!!:spank:

Exaclty, it'll be your base timing is too advanced or you have a lean out due to stuffed fuel pump, blocked injectors, broken fuel reg or blocked fuel filter.

Stop wasting time with all the other shit and get it to a proper workshop so they can stick a wideband in the exhaust and a timing light on then diagnose it as either timing or fuel.

Edited by Rolls

Would make more sense as it is extremely common for an annoying misfire at peak torque with stock tune skylines.

Pinging sounds like marbles being shaken around in a tin can, misfire sounds like the rev limiter, pop pop pop

Edited by Rolls

no need for a timing belt, timing light gave me a good reading

Just checking - you realise those two things are unrelated, right? I can't tell from your post.

The cam timing can be off and the spark timing can be fine, and the cam belt can be well past its reliable life, and the spark timing can be fine.

misfire sounds like the rev limiter, pop pop pop

it was making that noise heaps when hitting around 4000rpm... and also the pinging noise was just the intercooler pipe hitting the fan. ive replaced with a shorter bracket which pulls it away from the fan and sits nice and close to the timing cover.

i have fixed both problems but im in the proccess of getting a dyno and buying a timing kit, water pump cam belts. i am doing my best here in researching and learning more about the car.

it was making that noise heaps when hitting around 4000rpm... and also the pinging noise was just the intercooler pipe hitting the fan. ive replaced with a shorter bracket which pulls it away from the fan and sits nice and close to the timing cover.

i have fixed both problems but im in the proccess of getting a dyno and buying a timing kit, water pump cam belts. i am doing my best here in researching and learning more about the car.

might help to get your terminology right next time, would have give a completely different answer if you said misfiring and not pinging. Completely different things, detonation destroys motors, misfire is just annoying.

Elite/Rolls - holding all other things the same, wouldn't hot plugs slightly increase the tendency to ping?

I'm pretty sure a 5 is the hottest plug you can get in that size/thread/depth whatever. The factory listing is a 5. Like Rolls said, most unlikely.

Not impossible though. Usually dieseling is caused by lack of ignition timing or very lean mixtures

hmm well i had two sets of problems with the car... noises coming from here and there. The hitting noises were the fan hitting the intercooler pipe making the *tinging* noises .... thats fixed now..... and 4 out of 6 spark plugs were just absolutely f**ked..... i did buy NGK plugs.... good buy, fixed the misfire. currently driving the car at 2500 - 3000rpm. Everything seems to be fine ATM, but you guys have commented on the timing and cam belts, so i will be replacing them when i can.... i have seen the belts and they have seen better days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...