Jump to content
SAU Community

Recommended Posts

sparkplugs won't cause detonation, they can but it is highly unlikely in your situation, it almost certainly CAS base timing is advanced, you are not running 98 octane fuel, or it is a fuel issue and is leaning out.

Get it on a dyno and diagnose the issue, don't keep driving it or you WILL destroy the motor.

was hoping it was the spark plugs in my mind but have a feeling its not. plus when its idling and about to move forward in 1st.... i can hear a belt squeek in a way, been testing it while holding the brake and letting the clutch out i can hear it more......... its never done it before til this pinging noise.....

this car is my daily car, be hard for me to get around.......... imo ....its really annoying :)

sparkplugs won't cause detonation, they can but it is highly unlikely in your situation, it almost certainly CAS base timing is advanced, you are not running 98 octane fuel, or it is a fuel issue and is leaning out.

Get it on a dyno and diagnose the issue, don't keep driving it or you WILL destroy the motor.

+1 have a look at the CAS position , see if someones been messing with it.

.. imo ....its really annoying :)

having to replace the motor will be even more annoying, do not rev it past 4k and no boost until this is solved, I don't think you realise how serious this is. 10 seconds on full boost with sustained detonation is enough to melt ring lands.

having to replace the motor will be even more annoying, do not rev it past 4k and no boost until this is solved, I don't think you realise how serious this is. 10 seconds on full boost with sustained detonation is enough to melt ring lands.

yeah! what he said!!:spank:

Exaclty, it'll be your base timing is too advanced or you have a lean out due to stuffed fuel pump, blocked injectors, broken fuel reg or blocked fuel filter.

Stop wasting time with all the other shit and get it to a proper workshop so they can stick a wideband in the exhaust and a timing light on then diagnose it as either timing or fuel.

Edited by Rolls

Would make more sense as it is extremely common for an annoying misfire at peak torque with stock tune skylines.

Pinging sounds like marbles being shaken around in a tin can, misfire sounds like the rev limiter, pop pop pop

Edited by Rolls

no need for a timing belt, timing light gave me a good reading

Just checking - you realise those two things are unrelated, right? I can't tell from your post.

The cam timing can be off and the spark timing can be fine, and the cam belt can be well past its reliable life, and the spark timing can be fine.

misfire sounds like the rev limiter, pop pop pop

it was making that noise heaps when hitting around 4000rpm... and also the pinging noise was just the intercooler pipe hitting the fan. ive replaced with a shorter bracket which pulls it away from the fan and sits nice and close to the timing cover.

i have fixed both problems but im in the proccess of getting a dyno and buying a timing kit, water pump cam belts. i am doing my best here in researching and learning more about the car.

it was making that noise heaps when hitting around 4000rpm... and also the pinging noise was just the intercooler pipe hitting the fan. ive replaced with a shorter bracket which pulls it away from the fan and sits nice and close to the timing cover.

i have fixed both problems but im in the proccess of getting a dyno and buying a timing kit, water pump cam belts. i am doing my best here in researching and learning more about the car.

might help to get your terminology right next time, would have give a completely different answer if you said misfiring and not pinging. Completely different things, detonation destroys motors, misfire is just annoying.

Elite/Rolls - holding all other things the same, wouldn't hot plugs slightly increase the tendency to ping?

I'm pretty sure a 5 is the hottest plug you can get in that size/thread/depth whatever. The factory listing is a 5. Like Rolls said, most unlikely.

Not impossible though. Usually dieseling is caused by lack of ignition timing or very lean mixtures

hmm well i had two sets of problems with the car... noises coming from here and there. The hitting noises were the fan hitting the intercooler pipe making the *tinging* noises .... thats fixed now..... and 4 out of 6 spark plugs were just absolutely f**ked..... i did buy NGK plugs.... good buy, fixed the misfire. currently driving the car at 2500 - 3000rpm. Everything seems to be fine ATM, but you guys have commented on the timing and cam belts, so i will be replacing them when i can.... i have seen the belts and they have seen better days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...